Preparation Process and Properties of PEO Films with Low Thickness and High Corrosion Resistance on 2A12 Aluminum Alloy

ZHANG Jinyue, GUO Cean, SONG Meihua, ZHANG Wei, BAO Zebin, ZHU Liye, GAO Ge, WU Fengling, YANG Zhaoyu

Surface Technology ›› 2026, Vol. 55 ›› Issue (21) : 259-275.

PDF(9297 KB)
PDF(9297 KB)
Surface Technology ›› 2026, Vol. 55 ›› Issue (21) : 259-275. DOI: 10.16490/j.cnki.issn.1001-3660.2026.21.023
Equipment Surface Engineering

Preparation Process and Properties of PEO Films with Low Thickness and High Corrosion Resistance on 2A12 Aluminum Alloy

  • ZHANG Jinyue1, GUO Cean1,*, SONG Meihua2, ZHANG Wei3,*, BAO Zebin3, ZHU Liye4, GAO Ge5, WU Fengling5, YANG Zhaoyu5
Author information +
History +

Abstract

Aiming at the technical problems of the 5-15 μm ultra-thin 2A12 aluminum alloy plasma electrolytic oxidation (PEO) film layer with micropores, dense penetrating cracks and poor corrosion resistance, this paper does not rely on the thickening film layer to achieve anti-corrosion, and systematically studies the two original directions of precise matching of electrical parameters of the ultra-thin ceramic film and the chromium-free long-term sealing mechanism. In the experiment, 50 mm×50 mm×2 mm 2A12 aluminum alloy sample was used as the substrate, and the silicate electrolyte graphite cathode system was used. The five core electrical parameters of pulse frequency, positive/reverse duty cycle and positive/reverse input voltage were regulated by the control variable method. The full-dimensional characterization was completed by means of SEM, XRD, EDS, electrochemical workstation, neutral salt spray and 35 d long-term immersion EIS monitoring. The Zsimpwin software was used to fit the impedance data to construct a double equivalent circuit model, and the long-term protection differences of nickel acetate and potassium dichromate were compared. The optimal electrical parameter combination was determined by single factor electrochemical screening: frequency 800 Hz, forward duty cycle 30%, reverse duty cycle 20%, forward voltage 450 V, reverse voltage 55 V. Under these parameters, the single pulse energy was reduced, the heat accumulation was suppressed, the film layer generated a local non-porous dense area, the cross-section penetrating crack was completely eliminated, and the effective protection period of neutral salt spray was increased from 72 h to 168-288 h. The results of sealing experiment showed that neither of the two sealing agents changed the main phase of α-Al2O3 and γ-Al2O3 in the film layer, and the deposits only filled defects. The highest atomic ratio of Ni element in the pores of nickel acetate sealed sample was 51.63%, and the highest content of Cr element in the pores of potassium dichromate sealed sample was 12.53at.%. The polarization test showed that the self-corrosion current density of the nickel acetate sealed membrane was as low as 6×10-8 A/cm2, and the polarization resistance was 72.3 MΩ·cm2, which was 32 times and 78 times that of the potassium dichromate sealed and unsealed optimized membranes, respectively. After 35 days of continuous immersion EIS monitoring, a unique rule was found: the nickel acetate sealed sample maintained a complete capacitive arc throughout the whole process, and Warburg impedance appeared after 14 days of immersion, and the corrosion turned into slow diffusion control; after 21 days of potassium dichromate sealing, the impedance was greatly attenuated, and there was no diffusion control characteristic in the whole process of unsealed samples. In this paper, a hydrothermal three-stage sealing mechanism of nickel acetate was proposed: the hydroxyl site of the film adsorbed nickel ions, alumina hydrates to form AlOOH for initial sealing, nickel acetate hydrolyzes to form Ni(OH)2 and oxidizes to dense NiO precipitation, and the weak acidic environment strengthened the combination of the filler and the ceramic matrix to form a physical-chemical double barrier. In this study, ultra-high corrosion resistance was achieved on the 5-15 μm ultra-thin film layer by precise optimization of electrical parameters and chromium-free nickel acetate sealing. The matching criteria of electrical parameters of ultra-thin PEO film and the mechanism of nickel-based long-term sealing were established, which provided a new technical solution for low-cost and low-energy surface protection of lightweight weapon aluminum alloy.

Key words

2A12 aluminum alloy / plasma electrolytic oxidation / corrosion resistance / sealing post-treatment

Cite this article

Download Citations
ZHANG Jinyue, GUO Cean, SONG Meihua, ZHANG Wei, BAO Zebin, ZHU Liye, GAO Ge, WU Fengling, YANG Zhaoyu. Preparation Process and Properties of PEO Films with Low Thickness and High Corrosion Resistance on 2A12 Aluminum Alloy[J]. Surface Technology. 2026, 55(21): 259-275

References

[1] LIU X X.Study on Hot Extrusion Forming Technology of Aluminum Alloy Cartridge[D]. Nanjing: Nanjing University of Science and Technology, 2017.
[2] 范才河, 沈彤, 胡泽艺. 铝合金弹壳成形及失效分析[J]. 包装学报, 2019, 11(1): 87-93.
FAN C H, SHEN T, HU Z Y.Forming and Failure Analysis of Aluminum Alloy Cartridge Case[J]. Packaging Journal, 2019, 11(1): 87-93.
[3] 管仁国, 娄花芬, 黄晖, 等. 铝合金材料发展现状、趋势及展望[J]. 中国工程科学, 2020, 22(5): 68-75.
GUAN R G, LOU H F, HUANG H, et al.Development of Aluminum Alloy Materials: Current Status, Trend, and Prospects[J]. Strategic Study of CAE, 2020, 22(5): 68-75.
[4] 白玉洁, 孟迪, 李新义, 等. 高强铝合金模拟极寒大气环境下加速腐蚀机理研究[J]. 装备环境工程, 2025, 22(8): 1-13.
BAI Y J, MENG D, LI X Y, et al.Study on Accelerated Corrosion Mechanism of High-Strength Aluminum Alloy under Simulated Extremely Cold Atmospheric Environment[J]. Equipment Environmental Engineering, 2025, 22(8): 1-13.
[5] WU S, LIU C, ZHOU K, et al.Corrosion Behavior of 2A12 and 5A02 Aluminum Alloy in Typical Marine Atmosphere Environment[J]. Journal of Materials Research and Technology, 2025, 36: 9403-9412.
[6] 魏世丞, 姚巨坤, 易瑔, 等. 装备综合防护系统及其发展[J]. 装甲兵学报, 2022, 1(1): 104-108.
WEI S C, YAO J K, YI Q, et al.Comprehensive Equipment Protection System and Its Development[J]. Journal of Armored Forces, 2022, 1(1): 104-108.
[7] 蔡建, 胡秉飞, 赵耀辉. 基于适应高原环境的武器装备防护包装设计方法探讨[J]. 包装工程, 2009, 30(10): 54-58.
CAI J, HU B F, ZHAO Y H.On Protective Packaging Design Method of Ordnance Used in Plateau[J]. Packaging Engineering, 2009, 30(10): 54-58.
[8] 侯悦, 田原, 赵志鹏, 等. 海洋工程用铝合金的腐蚀与防护研究进展[J]. 表面技术, 2022, 51(5): 1-14.
HOU Y, TIAN Y, ZHAO Z P, et al.Corrosion and Protection of Aluminum Alloy for Marine Engineering[J]. Surface Technology, 2022, 51(5): 1-14.
[9] 杨帆. A320型飞机蒙皮2024-T3铝合金腐蚀机理及防护策略研究[J]. 中国机械, 2025(11): 11-14.
YANG F. Research on Corrosion Mechanism and Protection Strategies of2024-T3 Aluminum Alloy Skin for A320 Aircraft[J]. China Machinery, 2025(11): 11-14.
[10] 吕耀辉, 刘玉欣, 魏世丞, 等. 7A52铝合金等离子弧焊接头盐雾腐蚀行为研究[J]. 装备环境工程, 2018, 15(6): 65-69.
LYU Y H, LIU Y X, WEI S C, et al.Corrosion Behavior of 7A52 Aluminum Alloy Plasma Arc Welding Joint in Salt Water Spray[J]. Equipment Environmental Engineering, 2018, 15(6): 65-69.
[11] 陈永雄, 魏世丞, 梁秀兵, 等. 铝合金发动机缸盖的再制造技术研究[J]. 材料工程, 2012, 40(6): 16-20.
CHEN Y X, WEI S C, LIANG X B, et al.Research on Remanufacturing Process of a Typical Aluminum Alloy Engine Cylinder Head[J]. Journal of Materials Engineering, 2012, 40(6): 16-20.
[12] 张则敏, 遇宏. 导弹装备在沿海地区防腐蚀措施[J]. 装备环境工程, 2004, 1(2): 81-85.
ZHANG Z M, YU H.Anti-Corrosion Measures of Missile Equipment in Coastal Area[J]. Equipment Environmental Engineering, 2004, 1(2): 81-85.
[13] SIKDAR S, MENEZES P V, MACCIONE R, et al.Plasma Electrolytic Oxidation (PEO) Process—Processing, Properties, and Applications[J]. Nanomaterials, 2021, 11(6): 1375.
[14] YANG C, CHEN P H, WU W X, et al.A Review of Corrosion-Resistant PEO Coating on Mg Alloy[J]. Coatings, 2024, 14(4): 451.
[15] 刘一, 赵辰, 冯金宝, 等. 微弧氧化功能陶瓷涂层的设计及其在机械工程的应用进展[J]. 中国表面工程, 2025, 38(2): 167-192.
LIU Y, ZHAO C, FENG J B, et al.Progress on the Design of Functional Micro-Arc Oxidation Ceramic Coatings and Applications in Mechanical Engineering[J]. China Surface Engineering, 2025, 38(2): 167-192.
[16] 芦佳明. 铝合金阳极氧化无镍封闭工艺研究[D]. 南昌: 南昌航空大学, 2020.
LU J M.Study on Nickel Free Sealing Process of Anodic Oxidation of Aluminum Alloy[D]. Nanchang: Nanchang Hangkong University, 2020.
[17] LIU Y, ZHAO C, FENG J B, et al.Design of Functional Ceramic Coatings by Micro-Arc Oxidation and Their Application Progress in Mechanical Engineering[J]. China Surface Engineering, 2025, 38(2): 167-192.
[18] 李琦, 纪沙沙, 李万发, 等. 工艺参数对2A12铝合金微弧氧化膜层组织和腐蚀性能的影响[J]. 热加工工艺, 2021, 50(22): 108-112.
LI Q, JI S S, LI W F, et al.Effects of Process Parameters on Microstructure and Corrosion Properties of 2A12 Aluminum Alloy Micro-Arc Oxidation Films[J]. Hot Working Technology, 2021, 50(22): 108-112.
[19] 郭孟秋, 王长亮, 刘明, 等. 2A12合金微弧氧化工艺因素的影响研究[J]. 装备环境工程, 2008, 5(5): 38-41.
GUO M Q, WANG C L, LIU M, et al.Study of the Effect of 2A12 Al Alloy Micro-Arc Oxidation Process Factors[J]. Equipment Environmental Engineering, 2008, 5(5): 38-41.
[20] 陈鹿. 工艺参数及Ce(NO3)3对2A12铝合金微弧氧化膜形貌及性能的影响[D]. 哈尔滨: 哈尔滨理工大学, 2020.
CHEN L.Effects of Process Parameters and Ce(NO3)3 on the Morphology and Properties of Micro-Arc Oxide Films on 2A12 Aluminum Alloy[D]. Harbin: Harbin University of Technology, 2020.
[21] 窦宝捷. 铝合金微弧氧化膜封闭处理及其耐蚀机理研究[D]. 哈尔滨: 哈尔滨工程大学, 2017.
DOU B J.Posted Treatment of Microarc Oxidation Film on Al Alloy and Its Corrosion Performance[D]. Harbin: Harbin Engineering University, 2017.
[22] 张帅. 铝合金钻杆材料微弧氧化膜的封闭处理及其耐蚀机理研究[D]. 吉林: 吉林大学, 2024.
ZHANG S.Research on the Sealing Treatment of Micro-Arc Oxidation Film on Aluminum Alloy Drill Rod Materials and Its Corrosion Resistance Mechanism[D]. Jilin: Jilin University, 2024.
[23] 王平, 王春华, 杨军, 等. 封孔处理对ZL108铸铝微弧氧化膜性能的影响[J]. 材料保护, 2011, 44(10): 51-52.
WANG P, WANG C H, YANG J, et al.Effect of Sealing Treatment on Properties of Micro-Arc Oxidation Film of ZL108 Cast Aluminum Substrate[J]. Materials Protection, 2011, 44(10): 51-52.
[24] GUO Z Y, SONG J F, WANG G Q, et al.Enhancing the Tribological and Corrosion Properties of 2A12 Aluminum Alloy via Micro-Arc Oxidation and Paraffin Sealing[J]. Colloids and Surfaces A: Physicochemical and Engineering Aspects, 2025, 712: 136476.
[25] 郝国栋, 郭永良, 王超宇, 等. 微弧氧化陶瓷膜封孔后处理及抗高温氧化性能的研究[J]. 人工晶体学报, 2009, 38(S1): 339-341.
HAO G D, GUO Y L, WANG C Y, et al.Sealed Post Treatment of Ceramic Coatings by Micro-Arc Oxidation and Research of High Temperature Oxidation Resistence Property[J]. Journal of Synthetic Crystals, 2009, 38(S1): 339-341.
[26] 毛金明, 曹宇娟, 高磊, 等. 2A12铝合金微弧氧化电参数优化及膜层性能研究[J]. 热加工工艺, 2026, 55(9): 207-214.
MAO J M, CAO Y J, GAO L, et al.Electrical Parameter Optimization and Performance Evaluation of MAO Coatings on 2A12 Aluminum Alloy[J]. Hot Working Technology, 2026, 55(9): 207-214.
[27] 安凌云, 马颖, 王占营, 等. 微弧氧化工艺参数研究概况与展望[J]. 热加工工艺, 2020, 49(8): 1-8.
AN L Y, MA Y, WANG Z Y, et al.Research Situation and Prospect of Micro-Arc Oxidation Process Parameters[J]. Hot Working Technology, 2020, 49(8): 1-8.
[28] 林丹, 谷高扬, 商剑. 激光重熔处理对铝合金微弧氧化层组织及性能的影响[J]. 金属热处理, 2023, 48(4): 264-272.
LIN D, GU G Y, SHANG J.Effect of Laser Remelting on Microstructure and Properties of Micro-Arc Oxidation Layer on Aluminum Alloy[J]. Heat Treatment of Metals, 2023, 48(4): 264-272.
[29] 张纪磊. 动阴极条件下铝合金微弧氧化技术研究[D]. 烟台: 烟台大学, 2022.
ZHANG J L.Research on Micro-Arc Oxidation Technology of Aluminum Alloy under Moving Cathode Condition[D]. Yantai: Yantai University, 2022.
[30] 方雷, 马运柱, 刘文胜, 等. 氧化时间对铝合金微弧氧化膜层结构及耐腐蚀性能的影响[J]. 粉末冶金材料科学与工程, 2018, 23(5): 503-510.
FANG L, MA Y Z, LIU W S, et al.Effects of Oxidation Time on Microstructure and Corrosion Resistance of Micro-Arc Oxidation Film on Aluminum Alloy[J]. Materials Science and Engineering of Powder Metallurgy, 2018, 23(5): 503-510.
[31] 谢言. 电参数对微弧氧化能耗及膜层性能的影响研究[D]. 广州: 华南理工大学, 2014.
XIE Y.The Influence of electrical parameters on the energy consumption and properties of Ceramic Coating Fabricated by Micro Arc Oxidation[D]. Guangzhou: South China University of Technology, 2014.
[32] 张慧芳. 工艺参数对家居金属制品表面微弧氧化镀层性能的影响[J]. 电镀与精饰, 2026, 48(1): 53-60.
ZHANG H F.Effects of Process Parameters on Surface Micro-Arc Oxidation Coating Performance of Home Metal Products[J]. Plating & Finishing, 2026, 48(1): 53-60.
[33] 安凌云, 马颖, 剡晓旭, 等. 电参数及其交互作用对铝材等离子体电解氧化膜的影响[J]. 中国有色金属学会, 2020, 30(04): 883-895.
AN L Y, MA Y, SHAN X X, et al.Effects of Electrical Parameters and Their Interactions on the Plasma Electrolytic Oxide Film of Aluminum Materials[J]. Transactions of the China Nonferrous Metals Society, 2020, 30(04): 883-895.
[34] 朱剑威, 齐少豹, 李国栋, 等. 脉冲频率对铝基PEO涂层隔热性能的影响规律及作用机理[J]. 金属热处理, 2021, 46(7): 195-200.
ZHU J W, QI S B, LI G D, et al.Effect and Mechanism of Pulse Frequency on Thermal Property of Aluminum Based Plasma Electrolytic Oxidation Coating[J]. Heat Treatment of Metals, 2021, 46(7): 195-200.
[35] 刘建华, 李永星, 于美, 等. 三种无铬封闭方法对铝合金阳极氧化膜耐蚀性的影响[J]. 材料热处理学报, 2011, 32(10): 129-133.
LIU J H, LI Y X, YU M, et al.Effects of Chromium-Free Sealing Methods on Corrosion Resistance of Anodic Oxide Films on Aluminum Alloy[J]. Transactions of Materials and Heat Treatment, 2011, 32(10): 129-133.
[36] 叶作彦, 刘道新, 李重阳, 等. 封闭对铝合金微弧氧化膜在酸性溶液中耐蚀性的影响[J]. 无机材料学报, 2015, 30(6): 627-632.
YE Z Y, LIU D X, LI C Y, et al.Effect of Sealing Treatments on the Corrosion Behavior of Micro-Arc Oxidation Coating on Aluminum Alloy in Acid NaCl Solution[J]. Journal of Inorganic Materials, 2015, 30(6): 627-632.
[37] RUDNEV V S, LUKIYANCHUK I V, ADIGAMOVA M V, et al.The Effect of Nanocrystallites in the Pores of PEO Coatings on Their Magnetic Properties[J]. Surface and Coatings Technology, 2015, 269: 23-29.
[38] 孟令飞. 镁合金表面致密化防腐耐磨PEO陶瓷涂层的制备及性能研究[D]. 沈阳: 沈阳工业大学, 2022.
MENG L F.Preparation and Properties of Densified Anti-Corrosion and Wear-Rresistant PEO Ceramic Coatings on Magenesium Alloy Surface[D]. Shenyang: Shenyang University of Technology, 2022.
[39] 刘磊, 李来时, 吴玉胜, 等. 不同铝合金基体黑色微弧氧化膜的厚度对其结构和性能的影响[J]. 中国表面工程, 2023, 36(6): 163-177.
LIU L, LI L S, WU Y S, et al.Effect of Thickness on Structure and Property of Black Microarc Oxidation Coatings Prepared on Different Aluminum Alloys[J]. China Surface Engineering, 2023, 36(6): 163-177.
[40] 沈文宁, 王钰雯, 李庚, 等. 膜层厚度对6061铝合金黑色微弧氧化陶瓷膜层结构与性能的影响[J]. 材料保护, 2024, 57(2): 28-34.
SHEN W N, WANG Y W, LI G, et al.Effects of Coating Thickness on the Microstructure and Properties of Black Micro-Arc Oxidation Ceramic Coating on 6061 Aluminum Alloy[J]. Materials Protection, 2024, 57(2): 28-34.
[41] 曹京宜, 方志刚, 陈晋辉, 等. 5083铝合金表面单致密微弧氧化膜的制备及其性能研究[J]. 中国腐蚀与防护学报, 2020, 40(3): 251-258.
CAO J Y, FANG Z G, CHEN J H, et al.Preparation and Properties of Micro-Arc Oxide Film with Single Dense Layer on Surface of 5083 Aluminum Alloy[J]. Journal of Chinese Society for Corrosion and Protection, 2020, 40(3): 251-258.
[42] 李彤, 刘灿, 朱韵希, 等. 微弧氧化时间对7075铝合金陶瓷膜组织结构及性能的影响[J]. 兵器材料科学与工程, 2026, 49(4): 69-73.
LI T, LIU C, ZHU Y X, et al.Effect of Micro-Arc Oxidation Time on Microstructure and Properties of Ceramic Coatings on 7075 Aluminum Alloy[J]. Ordnance Material Science and Engineering, 2026, 49(4): 69-73.
[43] 郭爽, 杨景博, 白玉, 等. 石墨烯、氧化铝增强铝合金微弧氧化陶瓷层的耐蚀及耐磨性能[J]. 表面技术, 2025, 54(17): 117-125.
GUO S, YANG J B, BAI Y, et al.Corrosion Resistance and Wear Resistance of Aluminum Alloy MAO Coating Enhanced by Graphene and Nano-Aluminum[J]. Surface Technology, 2025, 54(17): 117-125.
[44] JO H, LEE S, KIM D, et al.Low Temperature Sealing of Anodized Aluminum Alloy for Enhancing Corrosion Resistance[J]. Materials, 2020, 13(21): 4904.

Funding

Inner Mongolia Autonomous Region Key R&D and Achievement Transformation Program Project (Science and Technology Supports the Revitalization of Northeast China) (2025YFDZ0066); the Key R&D Project of the Joint Science and Technology Program of Liaoning Province (2025JH2/101800434)
PDF(9297 KB)

Accesses

Citation

Detail

Sections
Recommended

/

〈 〉