Residual stress regulation and evolution in tungsten carbide (WC) films deposited by bipolar high-power impulse magnetron sputtering (BP-HiPIMS) were systematically investigated by independently adjusting the average sputtering power, working pressure, and deposition time while maintaining other deposition parameters unchanged, so as to clarify the relationship between process parameters, stress-state transition behaviors, and structural evolution during WC film growth. WC films were deposited on (100) silicon substrates using a WC target under different BP-HiPIMS conditions. The average residual stress was quantitatively evaluated using the wafer-curvature method combined with the Stoney equation. The effects of deposition parameters on stress evolution were further analyzed by correlating the stress results with the film thickness, deposition rate, surface and cross-sectional scanning electron microscopy (SEM) observations, and X-ray diffraction (XRD) characterization. The results demonstrated that the average sputtering power and working pressure were the dominant parameters controlling the residual stress state of WC films. Under power variation, the films deposited at 200-350 W exhibited compressive stress. The compressive stress magnitude initially decreased with the increase of power from 200 to 300 W, followed by a slight increase at 350 W. When the power was further increased to 400 W, the residual stress changed from compressive to tensile, reaching approximately +650 MPa. Therefore, the power-induced compressive-to-tensile stress transition was identified within the range of 350-400 W. A high-power deposition condition of 500 W resulted in severe cracking and local delamination of the film, indicating that the deposited layer no longer satisfied the requirements for reliable curvature-based stress evaluation. The working pressure also showed a significant influence on the stress state. Increasing the pressure from 2.0 to 4.0 Pa transformed the residual stress from compressive to tensile, with the transition occurring between 2.5 and 3.0 Pa. Unlike the power-dependent case, the apparent coherent diffraction domain size of the WC1-x(111) peak remained nearly unchanged in the pressure series, varying only within 3.0-3.2 nm. This indicated that the pressure-induced stress reversal was not primarily associated with significant changes in coherent diffraction domain size, but was more likely related to variations in gas-phase collision processes, particle transport behaviors, and the kinetic energy of depositing species. The influence of deposition time was investigated at 400 W and 3.0 Pa. All films deposited for 2-5 h exhibited tensile stress, while the stress evolution showed a non-monotonic trend. The tensile stress decreased initially with the increase of the deposition time, reached a minimum after 4 h, and subsequently increased during further deposition. This behavior suggested that stress evolution during thick-film growth was governed by the competition between stress relaxation associated with structural adjustment and the gradual accumulation of growth-related tensile stress. XRD analysis further revealed that increasing sputtering power significantly reduced the apparent coherent diffraction domain size of the WC1-x(111) peak from 14.2 nm to 3.1 nm, indicating continuous changes in the crystallization behavior during energetic particle bombardment. Combined with SEM observations, the results suggest that residual stress evolution in BP-HiPIMS WC films is controlled by the competition among ion-bombardment-induced compressive stress, particle transport characteristics, surface migration behavior, columnar growth evolution, and structural adjustment during film thickening. The identified stress-transition intervals and corresponding structural evolution provide important experimental guidance for selecting BP-HiPIMS process windows and optimizing the deposition of thick WC films with controlled residual stress.
Key words
BP-HiPIMS /
magnetron sputtering /
WC film /
residual stress /
process parameters
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
References
[1] WINDISCHMANN H.Intrinsic Stress in Sputter-Deposited Thin Films[J]. Critical Reviews in Solid State and Materials Sciences, 1992, 17(6): 547-596.
[2] SHEN Y G, MAI Y W, ZHANG Q C, et al.Residual Stress, Microstructure, and Structure of Tungsten Thin Films Deposited by Magnetron Sputtering[J]. Journal of Applied Physics, 2000, 87(1): 177-187.
[3] LUNDIN D, SARAKINOS K.An Introduction to Thin Film Processing Using High-Power Impulse Magnetron Sputtering[J]. Journal of Materials Research, 2012, 27(5): 780-792.
[4] 张蕊, 孟靖翔, 王铁钢, 等. 高功率脉冲磁控溅射及复合技术的研究进展[J]. 真空与低温, 2025, 31(1): 1-17.
ZHANG R, MENG J X, WANG T G, et al.Research Progress of Hybrid Technique High Power Impulse Magnetron Sputtering[J]. Vacuum and Cryogenics, 2025, 31(1): 1-17.
[5] SARAKINOS K, ALAMI J, KONSTANTINIDIS S.High Power Pulsed Magnetron Sputtering: A Review on Scientific and Engineering State of the Art[J]. Surface and Coatings Technology, 2010, 204(11): 1661-1684.
[6] ANDERS A.High Power Impulse Magnetron Sputtering and Related Discharges: Scalable Plasma Sources for Plasma-Based Ion Implantation and Deposition[J]. Surface and Coatings Technology, 2010, 204(18/19): 2864-2868.
[7] KERAUDY J, VILOAN R P B, RAADU M A, et al. Bipolar HiPIMS for Tailoring Ion Energies in Thin Film Deposition[J]. Surface and Coatings Technology, 2019, 359: 433-437.
[8] WU B H, HAEHNLEIN I, SHCHELKANOV I, et al.Cu Films Prepared by Bipolar Pulsed High Power Impulse Magnetron Sputtering[J]. Vacuum, 2018, 150: 216-221.
[9] DU H, ZANÁŠKA M, BRENNING N, et al. Bipolar HiPIMS: The Role of Capacitive Coupling in Achieving Ion Bombardment during Growth of Dielectric Thin Films[J]. Surface and Coatings Technology, 2021, 416: 127152.
[10] VILOAN R P B, GU J B, BOYD R, et al. Bipolar High Power Impulse Magnetron Sputtering for Energetic Ion Bombardment during TiN Thin Film Growth without the Use of a Substrate Bias[J]. Thin Solid Films, 2019, 688: 137350.
[11] DU H, ZANÁŠKA M, HELMERSSON U, et al. On Selective Ion Acceleration in Bipolar HiPIMS: A Case Study of (Al, Cr)2O3 Film Growth[J]. Surface and Coatings Technology, 2023, 454: 129153.
[12] VILOAN R P B, ZANÁŠKA M, LUNDIN D, et al. Pulse Length Selection for Optimizing the Accelerated Ion Flux Fraction of a Bipolar HiPIMS Discharge[J]. Plasma Sources Science and Technology, 2020, 29(12): 125013.
[13] VEPŘEK S, REIPRICH S. A Concept for the Design of Novel Superhard Coatings[J]. Thin Solid Films, 1995, 268(1/2): 64-71.
[14] KOHLSCHEEN J, BAREISS C.Combinatorial Deposition and Wear Testing of HiPIMS W-C Films[J]. Coatings, 2025, 15(1): 115.
[15] LOFAJ F, KABÁTOVÁ M, KLICH M, et al. The Comparison of Structure and Properties in DC Magnetron Sputtered and HiPIMS W-C: H Coatings with Different Hydrogen Content[J]. Ceramics International, 2019, 45(7): 9502-9514.
[16] GHAILANE A, MAKHA M, LARHLIMI H, et al.Design of Hard Coatings Deposited by HiPIMS and DCMS[J]. Materials Letters, 2020, 280: 128540.
[17] THORNTON J A, HOFFMAN D W.Internal Stresses in Titanium, Nickel, Molybdenum, and Tantalum Films Deposited by Cylindrical Magnetron Sputtering[J]. Journal of Vacuum Science and Technology, 1977, 14(1): 164-168.
[18] KAUB T, RAO Z X, CHASON E, et al.The Influence of Deposition Parameters on the Stress Evolution of Sputter Deposited Copper[J]. Surface and Coatings Technology, 2019, 357: 939-946.
[19] ABADIAS G, CHASON E, KECKES J, et al.Review Article: Stress in Thin Films and Coatings: Current Status, Challenges, and Prospects[J]. Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films, 2018, 36(2): 020801.
[20] JANSSEN G C A M, ABDALLA M M, VAN KEULEN F, et al. Celebrating the 100th Anniversary of the Stoney Equation for Film Stress: Developments from Polycrystalline Steel Strips to Single Crystal Silicon Wafers[J]. Thin Solid Films, 2009, 517(6): 1858-1867.
[21] RAO Z X, BERMAN S, YANG P L, et al.Understanding Residual Stress in Thin Films: Analyzing Wafer Curvature Measurements for Ag, Cu, Ni, Fe, Ti, and Cr with a Kinetic Model[J]. Journal of Applied Physics, 2021, 130(13): 135304.
[22] LIU H J, DAI M H, TIAN X Q, et al.Modified Stoney Formula for Determining Stress within Thin Films on Large-Deformation Isotropic Circular Plates[J]. AIP Advances, 2021, 11(12): 125009.
[23] JAMISON R D, SHEN Y L.Indentation-Derived Elastic Modulus of Multilayer Thin Films: Effect of Unloading-Induced Plasticity[J]. Journal of Materials Research, 2015, 30(15): 2279-2290.
[24] KUMAR D, MEENA R K, HIRSHIKESH, et al. Experimentally Validated Finite Element Model for Mechanical and Fracture Characteristics of SiCN Thin Films under Different Loads[J]. Scientific Reports, 2025, 15: 31759.
[25] ZHANG Y, CHEN Z Q, WU W D, et al.Focused Ion Beam (FIB) Prepared Microtextured Microneedle Array Capable of Delivering Drugs through Punctured Skin[J]. Scientific Reports, 2024, 14: 31489.
[26] OLIVEIRA J C, FERREIRA F, ANDERS A, et al.Reduced Atomic Shadowing in HiPIMS: Role of the Thermalized Metal Ions[J]. Applied Surface Science, 2018, 433: 934-944.
[27] NAZON J, HERBST M, MARCO DE LUCAS M C, et al. WC-Based Thin Films Obtained by Reactive Radio- Frequency Magnetron Sputtering Using W Target and Methane Gas[J]. Thin Solid Films, 2015, 591: 119-125.
[28] THORNTON J A.Influence of Apparatus Geometry and Deposition Conditions on the Structure and Topography of Thick Sputtered Coatings[J]. Journal of Vacuum Science and Technology, 1974, 11(4): 666-670.
[29] MONTI J M, STEWART J A, CUSTER J O, et al.Linking Simulated Polycrystalline Thin Film Microstructures to Physical Vapor Deposition Conditions[J]. Acta Materialia, 2023, 245: 118581.
[30] CHARGUI A, BEAINOU R E, MOSSET A, et al.Influence of Thickness and Sputtering Pressure on Electrical Resistivity and Elastic Wave Propagation in Oriented Columnar Tungsten Thin Films[J]. Nanomaterials, 2020, 10(1): 81.
[31] KOENIG T R, RAO Z X, CHASON E, et al.The Microstructural and Stress Evolution in Sputter Deposited Ni Thin Films[J]. Surface and Coatings Technology, 2021, 412: 126973.
[32] CHASON E, SU T.Understanding the Origins of Residual Stress in Thin Films through Measurements and Modeling[J]. JOM, 2025, 77(10): 7540-7558.
Funding
National Natural Science Foundation of China (52671097)