Effect of Mechanical Vibration Composite Treatment on the Performance of Laser-clad Ni-Fe-Based Gradient Coatings

CHEN Hao, CHENG Yanhai, GENG Jiaye, LIU Detao, ZHOU Jiali, YANG Jinyong, WANG Qingqing

Surface Technology ›› 2026, Vol. 55 ›› Issue (21) : 26-35.

PDF(18692 KB)
PDF(18692 KB)
Surface Technology ›› 2026, Vol. 55 ›› Issue (21) : 26-35. DOI: 10.16490/j.cnki.issn.1001-3660.2026.21.003
Surface and Interface Technology of Functional Components for Energy Equipment

Effect of Mechanical Vibration Composite Treatment on the Performance of Laser-clad Ni-Fe-Based Gradient Coatings

  • CHEN Hao, CHENG Yanhai*, GENG Jiaye, LIU Detao, ZHOU Jiali, YANG Jinyong, WANG Qingqing
Author information +
History +

Abstract

Coal processing equipment components are subjected to severe wear failure under extreme conditions, demanding efficient surface strengthening and repair techniques. In this work, Ni-Fe-based gradient coatings were deposited via mechanical vibration-assisted laser cladding, with vibration stress relief (VSR) applied during interpass intervals of every two layers to mitigate residual stress accumulation and reduce cracking susceptibility. Three types of specimens were prepared: direct cladding without vibration (S0), vibration-assisted cladding (V1), and vibration-assisted cladding combined with VSR (V2). The effects of vibration-assisted cladding and VSR on microstructure, microhardness, and wear resistance was systematically investigated.
Vibration-assisted coatings (V1, V2) exhibit no macroscopic surface cracks, whereas S0 shows surface-penetrating cracks perpendicular to the laser scanning direction, which is attributed to tensile thermal stresses caused by the sharp temperature gradient during rapid solidification. Mechanical vibration enhances melt pool convection, facilitates heat dissipation, and reduces the thermal gradient, thereby suppressing crack initiation and propagation. Microstructurally, all coatings show a transition from elongated columnar dendrites at the bottom to short dendrites and equiaxed grains in the interdendritic and intergranular regions at the top. The coating consists of Si-solid-solution α-Fe equiaxed grains and a eutectic structure containing retained austenite, (Fe,Cr)7C3, and Fe23(C,B)6. Vibration increases the eutectic area fraction, especially in the 8th layer, and refines equiaxed grains. Primary dendrite arm length decreases while arm width increases, indicating a lower temperature gradient and longer melt pool lifetime due to intensified melt flow. After VSR, refined equiaxed grains persist with higher number density and short-rod dendritic morphology. The topmost surface hardness of the V1 coating increases by 100HV0.3 compared with that of S0, while the V2 coating exhibits an increase of approximately 200HV0.3. V2 shows slightly higher hardness than V1, attributed to increased equiaxed grains numbers and dislocation strengthening from VSR.
Average coefficients of friction for S0, V1, and V2 are 0.868, 0.674, and 0.608, respectively, with corresponding average volume wear rates of 7.409×10-4, 0.511×10-4, and 0.499×10-4 mm3/(N·m). S0 presents a rough surface with numerous furrows, extensive delamination pits, and large debris, characteristic of abrasive wear accompanied by adhesive wear. V1 shows much more smooth regions, fewer furrows, and smearing features, indicating combined abrasive-adhesive wear with the latter intensified. However, a smooth protective layer is formed, and no large-scale tearing occurs due to the strong bonding of the refined eutectic structure. V2 shows the smoothest surface with narrower but more numerous furrows and negligible delamination, suggesting adhesive wear is substantially suppressed and only mild abrasive wear remains. EDS mapping shows that S0 forms a continuous Cr2O3-rich layer but also contains abundant oxidized debris. V1 and V2 have less oxide debris than S0 Interferometric measurements confirm the wear track depth and width of V1 and V2 are roughly 1/3 and 1/10 of those of S0, respectively. In all coatings, abrasive wear is the dominant mechanism, while the degree of adhesive wear first increases (S0→V1) and then decreases (V1→V2). This is explained by the interplay between microstructural refinement enhancing cohesion and increased local adhesion under vibration, the latter being mitigated by dislocation-induced suppression of plastic deformation after VSR. This work provides a theoretical foundation for regulating laser-clad Ni-Fe-based gradient coatings via mechanical vibration and offers a cost-effective route for improving surface performance of critical energy-equipment components.

Key words

laser cladding / functional gradient coatings / mechanical vibration / vibration aging / wear resistance

Cite this article

Download Citations
CHEN Hao, CHENG Yanhai, GENG Jiaye, LIU Detao, ZHOU Jiali, YANG Jinyong, WANG Qingqing. Effect of Mechanical Vibration Composite Treatment on the Performance of Laser-clad Ni-Fe-Based Gradient Coatings[J]. Surface Technology. 2026, 55(21): 26-35

References

[1] 孙旭东, 张博, 彭苏萍. 我国洁净煤技术2035发展趋势与战略对策研究[J]. 中国工程科学, 2020, 22(3): 132-140.
SUN X D, ZHANG B, PENG S P.Development Trend and Strategic Countermeasures of Clean Coal Technology in China Toward 2035[J]. Strategic Study of CAE, 2020, 22(3): 132-140.
[2] WANG J Y, CUI X F, ZHAO Y, et al.Microstructure and Performance Enhancement of the TiN/Fe-Based Cladding Layer Induced by Mechanical Vibration Assisted Underwater Wet Laser Cladding[J]. Surface and Coatings Technology, 2024, 476: 130176.
[3] 王传琦, 刘洪喜, 周荣, 等. 机械振动辅助激光熔覆NiCrBSi-TiC复合涂层中颗粒相行为特征[J]. 金属学报, 2013, 49(2): 221-228.
WANG C Q, LIU H X, ZHOU R, et al.Characteristic Behaviors of Particle Phases in NiCrBSi-TiC Composite Coating by Laser Cladding Assisted by Mechanical Vibration[J]. Acta Metallurgica Sinica, 2013, 49(2): 221-228.
[4] LIU H X, XU Q, WANG C Q, et al.Corrosion and Wear Behavior of Ni60CuMoW Coatings Fabricated by Combination of Laser Cladding and Mechanical Vibration Processing[J]. Journal of Alloys and Compounds, 2015, 621: 357-363.
[5] 刘洪喜, 陶喜德, 张晓伟, 等. 机械振动辅助激光熔覆Fe-Cr-Si-B-C涂层的显微组织及界面分布形态[J]. 光学精密工程, 2015, 23(8): 2192-2202.
LIU H X, TAO X D, ZHANG X W, et al.Microstructure and Interface Distribution of Fe-Cr-Si-B-C Laser Cladding Alloy Coatings Assisted by Mechanical Vibration[J]. Optics and Precision Engineering, 2015, 23(8): 2192-2202.
[6] YAO Z H, YU X W, NIE Y B, et al.Effects of Three-Dimensional Vibration on Laser Cladding of SS316L Alloy[J]. Journal of Laser Applications, 2019, 31(3): 032013.
[7] YAO Z H, CHEN J, QIAN H Y, et al.Microstructure and Tensile Property of Laser Cladding Assisted with Multidimensional High-Frequency Vibration[J]. Materials, 2022, 15(12): 4295.
[8] 俞晓文, 姚喆赫, 张操棋, 等. 多维高频振动对激光熔覆成形几何形貌的影响研究[J]. 表面技术, 2020, 49(10): 286-293.
YU X W, YAO Z H, ZHANG C Q, et al.Effects of Multi-Dimensional High Frequency Vibration on Geometrical Morphology of Laser Cladding Forming[J]. Surface Technology, 2020, 49(10): 286-293.
[9] PARIHAR R S, SETTI S G, SAHU R K.Recent Advances in the Manufacturing Processes of Functionally Graded Materials: A Review[J]. Science and Engineering of Composite Materials, 2018, 25(2): 309-336.
[10] ZHANG C, CHEN F, HUANG Z F, et al.Additive Manufacturing of Functionally Graded Materials: A Review[J]. Materials Science and Engineering: A, 2019, 764: 138209.
[11] 刘晓丹, 陶兴华, 韩振强. 振动时效工艺在消除膨胀波纹管残余应力中的应用[J]. 振动与冲击, 2015, 34(4): 171-174.
LIU X D, TAO X H, HAN Z Q.Application of Vibratory Stress Relief in Relaxation of Residual Stress for Expandable Corrugated Liners[J]. Journal of Vibration and Shock, 2015, 34(4): 171-174.
[12] MOHANTY S, ARIVARASU M, ARIVAZHAGAN N, et al.The Residual Stress Distribution of CO2 Laser Beam Welded AISI 316 Austenitic Stainless Steel and the Effect of Vibratory Stress Relief[J]. Materials Science and Engineering: A, 2017, 703: 227-235.
[13] ZHANG Q L, YU L, SHANG X F, et al.Residual Stress Relief of Welded Aluminum Alloy Plate Using Ultrasonic Vibration[J]. Ultrasonics, 2020, 107: 106164.
[14] 张群莉, 马黎娜, 陈智君, 等. 42CrMo表面激光熔覆铜合金涂层孔隙调控及摩擦磨损性能研究[J]. 表面技术, 2026, 55(2): 80-96.
ZHANG Q L, MA L N, CHEN Z J, et al.Porosity Regulation and Tribological Properties of Copper Alloy Coating on 42CrMo Steel by Laser Cladding[J]. Surface Technology, 2026, 55(2): 80-96.
[15] 绍璇. 振动辅助激光熔覆Fe基涂层组织与性能研究[D]. 徐州: 中国矿业大学, 2024.
SHAO X.Study on the Organization and Properties of Fe-Based Coatings by Vibration-Assisted Laser Cladding[D]. Xuzhou: China University of Mining Technology, 2024.
[16] ZHANG L, WANG S T, WANG H X, et al.Mechanical Properties and Microstructure Revolution of Vibration Assisted Wire Arc Additive Manufacturing 2319 Aluminum Alloy[J]. Materials Science and Engineering: A, 2023, 885: 145634.
[17] MA Q S, LI Y J, WANG J, et al.Microstructure Evolution and Growth Control of Ceramic Particles in Wide-Band Laser Clad Ni60/WC Composite Coatings[J]. Materials & Design, 2016, 92: 897-905.
[18] LI G J, LI J, LUO X.Effects of High Temperature Treatment on Microstructure and Mechanical Properties of Laser-Clad NiCrBSi/WC Coatings on Titanium Alloy Substrate[J]. Materials Characterization, 2014, 98: 83-92.
[19] 侯新宇, 邓进文, 吕静, 等. 激光扫描速度对Fe60合金熔覆层组织与力学性能的影响[J]. 表面工程与再制造, 2025, 25(1): 25-32.
HOU X Y, DENG J W, LYU J, et al.Effects of Laser Scanning Speed on the Structure and Mechanical Properties of Laser Cladding Fe60 Alloy Coating[J]. Surface Engineering & Remanufacturing, 2025, 25(1): 25-32.
[20] WANG X F, LI J.Study of the Wear Resistance of an Fe60/WC Composite Coating by Ultrasonic Assisted Laser Cladding[J]. Scientific Reports, 2025, 15: 8559.
[21] YANG J S, WANG Z M, SUN Z P, et al.Surface Strengthening Phenomenon and Mechanism of 6061 Solid Solution Alloy after Ultrasonic Stress Relief[J]. Materials Today Communications, 2023, 35: 105649.
[22] 王鑫, 赵恩兰, 王义赛, 等. 稀土Y2O3对激光熔覆Fe60-Y2O3涂层显微组织和摩擦学性能的影响[J]. 铸造技术, 2023, 44(7): 657-664.
WANG X, ZHAO E L, WANG Y S, et al.Microstructure and Tribological Properties of Laser Cladding Fe60-Y2O3Coating[J]. Foundry Technology, 2023, 44(7): 657-664.
[23] 刘麟, 詹普杰, 刘文明, 等. 基于原位和RNT技术的铜锌合金摩擦磨损性能[J]. 摩擦学学报, 2016, 36(5): 577-584.
LIU L, ZHAN P J, LIU W M, et al.Friction and Wear Behavior of Copper-Zinc Alloy Based on In-Situ Holographic Microscopy and Radionuclide Technique[J]. Tribology, 2016, 36(5): 577-584.
[24] CAO J L, TENG H, WANG W R, et al.Tribological Properties of the 40Cr/GCr15 Tribo-Pair under Unidirectional Rotary and Reciprocating Dry Sliding[J]. Coatings, 2022, 12(5): 557.
[25] EL-RAGHY T, BLAU P, BARSOUM M W.Effect of Grain Size on Friction and Wear Behavior of Ti3SiC2[J]. Wear, 2000, 238(2): 125-130.
[26] GUU Y Y, LIN J F, AI C F.Correlation between Three-Body Wear and Tribological Characteristics of Titanium Nitride, Titanium Carbonitride and Titanium Carbide Coatings[J]. Wear, 1997, 208(1/2): 147-154.
[27] MATHIOU C, POULIA A, GEORGATIS E, et al.Microstructural Features and Dry-Sliding Wear Response of MoTaNbZrTi High Entropy Alloy[J]. Materials Chemistry and Physics, 2018, 210: 126-135.
[28] 张永振. 材料的干摩擦学[M]. 第2版. 北京: 科学出版社, 2012: 421.
ZHANG Y Z.Dry Tribology of Materials[M]. 2nd Edition. Beijing: Science Press, 2012: 421.
[29] ZHOU J L, CHENG Y H, CHEN H, et al.Mechanical Vibration-Assisted High-Speed Laser Cladding of Ceramic Particle-Reinforced High Entropy Alloy with Gradient Structures[J]. Applied Surface Science, 2026, 720: 165275.

Funding

The National Key Research and Development Program of China (2023YFE0201600); the Priority Academic Program Development of Jiangsu Higher Education Institutions (PAPD)
PDF(18692 KB)

Accesses

Citation

Detail

Sections
Recommended

/

〈 〉