目的 针对碳纤维/聚酰亚胺(CF/PI)复合材料界面结合力弱且高温环境下界面强度退化严重的瓶颈问题,通过界面工程构筑强韧且耐热的新型界面相。方法 设计并制备一种含苯乙炔封端的聚酰亚胺(PETI)耐高温上浆剂,系统探究上浆浓度(0%~2.0%)对T800碳纤维表面理化特性,以及复合材料宏观力学与热力学性能的影响规律。结果 1.0%为实现界面强化的最佳上浆浓度,微观表征证实,该浓度下PETI在纤维表面形成了均匀连续的包覆层,引入的高活性极性官能团使碳纤维的表面自由能由36.96 mN/m显著提升至50.70 mN/m。基于优化后的界面结构,复合材料的性能实现显著提升,其常温层间剪切强度(ILSS)达到109.7 MPa,较未处理样品提升15.1%,在300 ℃苛刻热环境下,其ILSS仍高达51.5 MPa,较未处理样品(32.0 MPa)实现了61.0%的大幅提升。此外,复合材料的玻璃化转变温度(tg)从404 ℃提高至425 ℃。结论 适量的PETI上浆剂通过与碳纤维形成π-π相互作用,并与树脂基体发生分子链缠结,成功构建了高效的界面桥联网络。其卓越的本征热稳定性有效充当了热屏障,不仅大幅强化了常温界面强度,更突破了复合材料高温界面易失效的难题。
Abstract
To address weak interfacial bonding strength and degradation at elevated temperatures in carbon fiber/polyimide (CF/PI) composites, the work aims to construct an interfacial phase with enhanced strength and heat resistance via interface engineering. A high-temperature-resistant sizing agent containing phenylethynyl-terminated polyimide (PETI) was designed and synthesized. The synthesis involved reacting 4-phenylethynylphthalic anhydride (PEPA), 3,3',4,4'-biphenyltetracarboxylic dianhydride (BTDA), and 2,2'-dimethylbenzidine (DMBZ) at a molar ratio of 2:2:3. Fourier transform infrared (FTIR) spectroscopy revealed an absorption peak at 2 213 cm-1, confirming the integration of phenylethynyl end-capping groups into the polyimide prepolymer chains. Proton nuclear magnetic resonance (1H NMR) spectroscopy verified the molecular architecture, confirming the absence of terminal alkyne protons and aligning with the internal alkyne structure of PEPA. T800 carbon fibers were desized using acetone and coated with varying mass fractions (0wt.%-2.0wt.%) of PETI sizing solutions. Unidirectional prepregs were prepared, controlling the resin mass fraction to approximately 42%, and composites were fabricated through a step-curing up to 380 ℃ under 5 MPa pressure. Microstructural characterizations established 1.0wt.% as the optimal concentration for interfacial reinforcement. Scanning electron microscopy (SEM) showed that at 1.0wt.%, the PETI sizing agent formed a uniform and continuous coating layer that filled the longitudinal surface grooves of the carbon fibers. Lower concentrations provided incomplete coverage, while higher concentrations resulted in polymer agglomeration and non-uniform thickness, which could evolve into defect layers. X-ray photoelectron spectroscopy (XPS) indicated a change in surface chemistry following the sizing treatment. The nitrogen content increased from 1.58% in untreated fibers to 3.54% in the 1.0wt.% treated fibers. High-resolution C1s spectra deconvolution confirmed the introduction of polar functional groups, with relative contents of C—N and O—C=O reaching 18.33% and 5.59%, respectively. Dynamic contact angle measurements confirmed that these polar moieties improved the wettability of the fibers. The water contact angle decreased from 76.89° to 60.73°. The total surface free energy increased from 36.96 mN/m to 50.70 mN/m, primarily due to an increase in the polar component, providing a thermodynamic foundation for matrix resin penetration. Thermogravimetric analysis (TGA) showcased the thermal stability of the PETI sizing agent, with 5% and 10% thermal weight loss temperatures of 497.05 ℃ and 544.39 ℃, respectively. This surpassed the thermal resilience of the polyimide resin (PI-NA) matrix, ensuring that the sizing layer acted as a thermal barrier during the curing process. Mechanical testing illustrated the impact of the modified interface. The interlaminar shear strength (ILSS) of the 1.0wt% modified composite at room temperature reached 109.7 MPa, a 15.1% improvement over untreated samples (95.3 MPa). Under thermal conditions at 300 ℃, the interfacial phase maintained structural integrity, with the ILSS remaining at 51.5 MPa. This performance represented a 61.0% enhancement compared to untreated samples (32.0 MPa). Dynamic mechanical analysis (DMA) revealed that the glass transition temperature (tg) of the composite advanced from 404 ℃ to 425 ℃. Mechanistically, the interfacial architecture functioned through a dual-bridging effect. On the carbon fiber side, polar aromatic heterocycles in the PETI chains established π-π interactions and hydrogen-bonding networks with oxygen-containing functional groups on the surface. On the matrix side, the PETI sizing layer underwent diffusion, molecular chain entanglement, and co-crosslinking with the PI-NA resin matrix. Fractographic analyses via SEM confirms that this interfacial network transfers mechanical stress, shifting the failure mode from interfacial debonding to resin cohesive failure. In conclusion, 1.0wt% PETI constructs an interfacial bridging network, addressing high-temperature interfacial failure in CF/PI composites.
关键词
碳纤维 /
聚酰亚胺 /
界面改性 /
上浆剂 /
复合材料
Key words
carbon fiber /
polyimide /
interface modification /
sizing agent /
composite
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
参考文献
[1] 荆云娟, 崔博, 马军, 等. 碳纤维复合材料产业链发展现状[J]. 合成纤维, 2023, 52(10): 37-42.
JING Y J, CUI B, MA J, et al.Development Status of Carbon Fiber Composites Industry Chain[J]. Synthetic Fiber in China, 2023, 52(10): 37-42.
[2] 薛书宇, 雷星锋, 连如贺, 等. 高性能热固性聚酰亚胺树脂研究进展[J]. 高分子材料科学与工程, 2021, 37(5): 149-162.
XUE S Y, LEI X F, LIAN R H, et al.Progress of High-Performance Thermosetting Polyimide Resins[J]. Polymer Materials Science & Engineering, 2021, 37(5): 149-162.
[3] CHEN J L, WANG K, ZHAO Y.Enhanced Interfacial Interactions of Carbon Fiber Reinforced PEEK Composites by Regulating PEI and Graphene Oxide Complex Sizing at the Interface[J]. Composites Science and Technology, 2018, 154: 175-186.
[4] 王臣辉. 碳纤维上浆剂对复合材料界面性能的影响研究进展[J]. 化工与医药工程, 2023, 44(2): 1-7.
WANG C H.Research Progress on the Influence of Carbon Fiber Sizing Agents on the Interfacial Properties of Composites[J]. Chemical and Pharmaceutical Engineering, 2023, 44(2): 1-7.
[5] CHEN Y F, DING L, CUI C, et al.A Simple Way to Synthesize a Nano-Scale Stable Epoxy Emulsion for Sizing CF/Epoxy Composites[J]. New Journal of Chemistry, 2021, 45(48): 22860-22868.
[6] 张文姝, 王方义, 王亚宁, 等. 拉曼光谱在碳纤维增强复合材料性能研究中的应用[J]. 分析测试学报, 2024, 43(9): 1301-1309.
ZHANG W S, WANG F Y, WANG Y N, et al.Application of Raman Spectroscopy in the Study of Carbon Fiber Reinforced Composite Materials' Properties[J]. Journal of Instrumental Analysis, 2024, 43(9): 1301-1309.
[7] 李天舒, 王绍凯, 武清, 等. 宇航级T800碳纤维复合材料界面调控[J]. 北京航空航天大学学报, 2023, 49(8): 2011-2020.
LI T S, WANG S K, WU Q, et al.Interface Adjustment of Aerospace-Grade T800carbon Fiber Composite Material[J]. Journal of Beijing University of Aeronautics and Astronautics, 2023, 49(8): 2011-2020.
[8] HASSAN E A M, GE D T, ZHU S, et al. Enhancing CF/PEEK Composites by CF Decoration with Polyimide and Loosely-Packed CNT Arrays[J]. Composites Part A: Applied Science and Manufacturing, 2019, 127: 105613.
[9] 钟敏, 王进, 刘杰, 等. 苯乙炔基封端型聚酰亚胺树脂及复合材料的制备与性能研究[J]. 高分子通报, 2024, 37(8): 1108-1116.
ZHONG M, WANG J, LIU J, et al.Preparation and Properties of Phenylethynyl-Terminated Polyimide Resins and Composites[J]. Polymer Bulletin, 2024, 37(8): 1108-1116.
[10] QIU Z J, WANG Y L, LI C S, et al.Interfacial Strengthening of Carbon Fiber/Epoxy Composites through a Sulfonated High-Epoxy-Value Sizing Agent[J]. Surfaces and Interfaces, 2023, 36: 102394.
[11] PAWAR S S, HUTCHINSON S A, EYCKENS D J, et al.Designing Carbon Fiber Composite Interfaces: Reactive Sizing Derived from Terpenes[J]. Industrial & Engineering Chemistry Research, 2023, 62(7): 3157-3164.
[12] WANG S D, WANG T J, ZHANG S W, et al.Enhancing Fiber-Matrix Interface in Carbon Fiber/Poly Ether Ether Ketone (CF/PEEK) Composites by Carbon Nanotube Reinforcement of Crystalline PEEK Sizing[J]. Composites Part B: Engineering, 2023, 251: 110470.
[13] 秦建杰. 碳纤维表面连续生长碳纳米管及其增强复合材料的研究[D]. 济南: 山东大学, 2021.
QIN J J.Study on the Continuous Growth of Carbon Nanotubes on Carbon Fiber Surfaces and Their Reinforced Composites[D]. Jinan: Shandong University, 2021.
[14] QIU Z J, WANG Y L, LI C S, et al.Interlaminar Improvement of Carbon Fiber/Epoxy Composites via Fluorine-Containing High-Epoxy-Value Sizing Agent[J]. Journal of Applied Polymer Science, 2022, 139(30): e52665.
[15] PAWAR S S, HUTCHINSON S A, EYCKENS D J, et al.Carbon Fiber Sizing Agents Based on Renewable Terpenes[J]. Composites Science and Technology, 2022, 220: 109280.
[16] YANG C Y, XU W X, NAN Y, et al.Fabrication and Characterization of a High Performance Polyimide Ultrafiltration Membrane for Dye Removal[J]. Journal of Colloid and Interface Science, 2020, 562: 589-597.
[17] KIM J, KIM G, KIM S Y, et al.Fabrication of Highly Flexible Electromagnetic Interference Shielding Polyimide Carbon Black Composite Using Hot-Pressing Method[J]. Composites Part B: Engineering, 2021, 221: 109010.
[18] DUAN C J, HE R, LI S, et al.Effect of Atomic Oxygen on Corrosion and Friction and Wear Behavior of Polyimide Composites[J]. Journal of Applied Polymer Science, 2020, 137(10): 48441.
[19] DUAN C J, HE R, LI S, et al.Exploring the Friction and Wear Behaviors of Ag-Mo Hybrid Modified Thermosetting Polyimide Composites at High Temperature[J]. Friction, 2020, 8(5): 893-904.
[20] 曹贤武, 韦创, 何光建, 等. 四元共聚热塑性聚酰亚胺的合成与表征[J]. 华南理工大学学报(自然科学版), 2020, 48(4): 73-79.
CAO X W, WEI C, HE G J, et al.Synthesis and Characterization of Quaternary Copolymerized Thermoplastic Polyimide[J]. Journal of South China University of Technology (Natural Science Edition), 2020, 48(4): 73-79.
[21] 钟敏, 刘杰, 江乾, 等. PMR型耐高温聚酰亚胺基体树脂及复合材料的制备与性能研究[J]. 化工新型材料, 2023, 51(11): 111-117.
ZHONG M, LIU J, JIANG Q, et al.Preparation and Properties of PMR-Type High-Temperature Resistant Polyimide Matrix Resins and Composites[J]. New Chemical Materials, 2023, 51(11): 111-117.
[22] HONG W J, YUAN L L, ZHANG H Y, et al.Phenylethynyl-Terminated Imide Oligomers Modified by Reactive Diluent for Resin Transfer Molding Application[J]. Chinese Journal of Polymer Science, 2022, 40(1): 107-120.
[23] LI K D, DING J H, GUO Y X, et al.Direct Ink Writing of Phenylethynyl End-Capped Oligoimide/SiO2 to Additively Manufacture High-Performance Thermosetting Polyimide Composites[J]. Polymers, 2022, 14(13): 2669.
[24] LIU Y, XU X Z, MO S, et al.Long-Term Thermo- Oxidative Degradation Modeling of a Carbon Fiber Reinforced Polyimide Composite: Multistep Degradation Behaviors and Kinetics[J]. Chinese Journal of Polymer Science, 2020, 38(11): 1202-1213.
[25] YIM D, YOON S K, JANG S, et al.Development of High-Performance Composites with Molecular Weight Controlled Polyimide Oligomers End-Capped with Phenylethynyl Groups[J]. Fibers and Polymers, 2020, 21(12): 2907-2914.
基金
辽宁省兴辽英才计划项目(XLYC2402058)