基于激光冲击强化前后处理软件的TC6钛合金数值模拟

朱然, 孔垂江, 王兴法, 徐继康, 杨俊茹, 孙博宇

表面技术 ›› 2026, Vol. 55 ›› Issue (21) : 179-190.

PDF(7312 KB)
PDF(7312 KB)
表面技术 ›› 2026, Vol. 55 ›› Issue (21) : 179-190. DOI: 10.16490/j.cnki.issn.1001-3660.2026.21.016
表界面强化技术

基于激光冲击强化前后处理软件的TC6钛合金数值模拟

  • 朱然1, 孔垂江1, 王兴法2, 徐继康3, 杨俊茹1,*, 孙博宇4
作者信息 +

Numerical Simulation of TC6 Titanium Alloy Based on Laser Shock Peening Pre- and Post-processing Software

  • ZHU Ran1, KONG Chuijiang1, WANG Xingfa2, XU Jikang3, YANG Junru1,*, SUN Boyu4
Author information +
文章历史 +

摘要

目的 提高激光冲击强化仿真(LSP)前、后处理效率。方法 基于C/C++采用MVC架构开发一款LSP前后处理软件。首先,选取5、6 J激光能量对TC6钛合金试样进行激光冲击处理,通过软件对比仿真模型精度。其次,研究不同激光工艺参数对残余应力分布的影响。最后,利用该软件对曲面扇叶和齿轮进行LSP仿真。结果 经试验对比,5、6 J残余压应力最大相对误差分别为11.4%、7.4%,深度方向最大绝对误差分别为25.0、18.9MPa,有限元模型可靠。此外,在5、6、7 J激光能量条件下,表面平均残余压应力随激光能量的增加而增大,残余应力波动增大,值依次为543.6、597.2、634.7 MPa,残余压应力影响层深度增加,最大深度为0.48 mm。激光能量为6 J时,进行1、2、3次激光冲击,表面平均残余压应力随冲击次数的增加而增大,增幅减小,残余压应力值依次为597.2、763.9、841.5 MPa,残余压应力影响层深度增加,最大深度为0.58 mm。针对叶片和齿轮进行LSP仿真,在叶片边缘、齿轮齿根处形成200、409 MPa的残余压应力。结论 基于该软件能够快速构建简单、复杂曲面激光冲击有限元模型,提高了LSP前后处理效率。

Abstract

To improve the preprocessing and postprocessing efficiency of laser shock peening (LSP) numerical simulations, dedicated LSP pre- and post-processing software was developed in C/C++ under the Model-View-Controller (MVC) architecture. A complete set of interactive Python application programming interfaces (APIs) was encapsulated to support automated scripting workflows, and an extensible software kernel was constructed based on the Qt plugin framework. Multiple functional plugins covering one-click planar LSP simulation, post-processing format conversion and residual stress field extraction were integrated into the software system. An interactive wizard-based finite element modeling module for components with complex curved surfaces was specially designed to facilitate the LSP numerical simulation of various mechanical parts. LSP experiments were conducted on TC6 titanium alloy specimens at laser energies of5 J and 6 J. Simulated residual stress results output from the software were compared with experimental measurements to validate the prediction accuracy of finite element models. Numerical simulations were performed at laser energies of 5 J, 6 J and 7 J to investigate the effects of laser energy on residual stress distribution. With a fixed laser energy of 6 J, additional numerical simulations with 1, 2 and 3 sequential LSP impacts were implemented to analyze the influence of impact times on residual stress fields. Finally, the established software was applied to conduct LSP numerical simulations for curved fan blades and gear components. Comparative analysis between simulation and experimental data showed that the maximum relative errors of surface compressive residual stress at laser energies of 5 J and 6 J were 11.4% and 7.4%, respectively, while the maximum absolute errors along the depth direction were 25.0 MPa and 18.9 MPa. These results verified the reliability and accuracy of the established finite element models. Under laser energies of 5 J, 6 J and 7 J, the average surface compressive residual stress increased with rising laser energy, with values of 543.6 MPa, 597.2 MPa and 634.7 MPa, respectively. The depth of the compressive residual stress-affected zone correspondingly increased to 0.38 mm, 0.44 mm and 0.48 mm. At a fixed laser energy of 6 J with 1, 2 and 3 sequential LSP impacts, the average surface compressive residual stress increased with rising impact times, whereas the growth rate gradually declined, with values of 597.2 MPa, 763.9 MPa and 841.5 MPa, respectively, and the depths of the affected layers expanded to 0.44 mm, 0.51 mm and 0.58 mm, respectively. LSP simulations for blade edges and gear tooth roots yielded compressive residual stresses of 200 MPa and 409 MPa in these critical structural regions. Such residual stress characteristics provided favorable mechanical conditions for improving the fatigue performance of mechanical structural components. The developed software can be applied to typical complex-curved-surface components such as blades and gears. It reduces the pre- and post-processing time of LSP finite-element models for complex curved components from tens of minutes to hours in traditional manual operations to the minute level, achieving at least a 10-fold efficiency improvement for LSP numerical simulation.

关键词

数值模拟 / TC6钛合金 / 激光冲击强化 / C/C++软件开发 / 软件设计模式 / MVC

Key words

numerical simulation / TC6 titanium alloy / laser shock peening (LSP) / C/C++ software development / software design patterns / MVC

引用本文

导出引用
朱然, 孔垂江, 王兴法, 徐继康, 杨俊茹, 孙博宇. 基于激光冲击强化前后处理软件的TC6钛合金数值模拟[J]. 表面技术. 2026, 55(21): 179-190
ZHU Ran, KONG Chuijiang, WANG Xingfa, XU Jikang, YANG Junru, SUN Boyu. Numerical Simulation of TC6 Titanium Alloy Based on Laser Shock Peening Pre- and Post-processing Software[J]. Surface Technology. 2026, 55(21): 179-190
中图分类号: TN249   

参考文献

[1] UMAPATHI A, SWAROOP S.Deformation of Single and Multiple Laser Peened TC6 Titanium Alloy[J]. Optics & Laser Technology, 2018, 100: 309-316.
[2] LI C G, FU H Z, YU Q.Aerospace Materials[M]. 4th ed. Beijing: National Defense Industry Press, 2002: 41-55.
[3] WARZANSKYJ W, ANGULO I, CORDOVILLA F, et al.Analysis of the Thermal Stability of Residual Stresses Induced in Ti-6Al-4 V by High Density LSP Treatments[J]. Journal of Alloys and Compounds, 2023, 931: 167530.
[4] CORREA C, RUIZ DE LARA L, DÍAZ M, et al. Influence of Pulse Sequence and Edge Material Effect on Fatigue Life of Al2024-T351 Specimens Treated by Laser Shock Processing[J]. International Journal of Fatigue, 2015, 70: 196-204.
[5] RUBIO-GONZÁLEZ C, OCAÑA J L, GOMEZ-ROSAS G, et al. Effect of Laser Shock Processing on Fatigue Crack Growth and Fracture Toughness of 6061-T6 Aluminum Alloy[J]. Materials Science and Engineering: A, 2004, 386(1/2): 291-295.
[6] REN X D, ZHAN Q B, YUAN S Q, et al.A Finite Element Analysis of Thermal Relaxation of Residual Stress in Laser Shock Processing Ni-Based Alloy GH4169[J]. Materials & Design (1980-2015), 2014, 54: 708-711.
[7] CAI S P, ZHANG Y K.An Iterative Approach Combined with Multi-Dimensional Fitting of Limited Measured Stress Points to Reconstruct Residual Stress Field Generated by Laser Shock Peening[J]. Surface and Coatings Technology, 2022, 436: 128237.
[8] PEYRE P, FABBRO R, MERRIEN P, et al.Laser Shock Processing of Aluminium Alloys. Application to High Cycle Fatigue Behaviour[J]. Materials Science and Engineering: A, 1996, 210(1/2): 102-113.
[9] CLAUER A H, LAHRMAN D F.Laser Shock Processing as a Surface Enhancement Process[J]. Key Engineering Materials, 2001, 197: 121-144.
[10] 韩正旭, 唐进元, 邵文, 等. 航空齿轮激光冲击强化残余应力场仿真计算研究[J]. 航空制造技术, 2023, 66(5): 91-102.
HAN Z X, TANG J Y, SHAO W, et al.A Numerical Simulation Study on Residual Stress Distribution in Laser Shock Peening of Aviation Gear[J]. Aeronautical Manufacturing Technology, 2023, 66(5): 91-102.
[11] 范龙岗. 航空齿轮齿面激光冲击强化仿真与试验研究[D]. 南昌: 南昌航空大学, 2023: 20-31.
FAN L G.Simulation and experimental research on laser shock peening of aviation gear tooth surfaces[D]. Nanchang: Nanchang Hangkong University, 2023: 20-31.
[12] 宣宏林. 激光冲击强化钛合金材料数值模拟[J]. 机械制造与自动化, 2023, 52(6): 116-118.
XUAN H L.Numerical Simulation of External Damage of Titanium Alloy Materials Strengthened by Laser Shock[J]. Machine Building & Automation, 2023, 52(6): 116-118.
[13] 周思柱, 杨子彧, 李林, 等. 激光冲击强化下泵头体材料表面残余应力演化仿真及试验研究[J]. 现代制造工程, 2025(6): 1-10.
ZHOU S Z, YANG Z Y, LI L, et al.Simulation and Experimental Research on Residual Stress Evolution on the Surface of Pump Head Body Material under Laser Shock Strengthening[J]. Modern Manufacturing Engineering, 2025(6): 1-10.
[14] 田子航, 孙博宇, 金丹, 等. 激光冲击强化对TC11钛合金应力松弛特性的影响[J]. 航空制造技术, 2025, 68(13): 100-105.
TIAN Z H, SUN B Y, JIN D, et al.Effect of Laser Shock Peening on Stress Relaxation Characteristics of TC11 Titanium Alloy[J]. Aeronautical Manufacturing Technology, 2025, 68(13): 100-105.
[15] 葛良辰, 曹宇鹏, 花国然, 等. 表面曲率对激光冲击曲面材料表面残余应力场分布的影响[J]. 表面技术, 2020, 49(4): 284-291.
GE L C, CAO Y P, HUA G R, et al.The Effect of Surface Curvature on Surface Residual Stress Field Distribution of Laser Shock Materials[J]. Surface Technology, 2020, 49(4): 284-291.
[16] 马永新, 王浩, 陆越, 等. 激光冲击强化对TC4钛合金表面性能的影响[J]. 应用激光, 2025, 45(8): 129-135.
MA Y X, WANG H, LU Y, et al.Effect of Laser Shock Peening on the Surface Properties of TC4 Titanium Alloy[J]. Applied Laser, 2025, 45(8): 129-135.
[17] 汤洋, 廖一凡, 李斯魏, 等. TC4钛合金叶片双面同时激光斜冲击强化研究[J]. 机械工程与自动化, 2024, 53(3): 103-104.
TANG Y, LIAO Y F, LI S W, et al.Study of Double-Sided Simultaneous Laser Oblique Shock Peening Strengthening of TC4 Titanium Alloy Blades[J]. Mechanical Engineering & Automation, 2024, 53(3): 103-104.
[18] 尚一博, 伏宇, 张璇, 等. 激光冲击强化TC17钛合金叶片高周疲劳强度评估模型[J]. 表面技术, 2025, 54(11): 184-194.
SHANG Y B, FU Y, ZHANG X, et al.High Cycle Fatigue Strength Evaluation Model for TC17 Titanium Alloy Blades Strengthened by Laser Shock Peening[J]. Surface Technology, 2025, 54(11): 184-194.
[19] 邓洋洋, 杨扬. 激光粉末床熔融制备Ti6Al4V合金初始残余应力对激光冲击强化诱生残余应力场影响研究[J]. 矿冶工程, 2025, 45(5): 164-169.
DENG Y Y, YANG Y.Influence of Initial Residual Stress of Ti6Al4V Alloy Prepared by Laser Powder Bed Fusion on Laser Shock Peening-Induced Residual Stress Field[J]. Mining and Metallurgical Engineering, 2025, 45(5): 164-169.
[20] 何国旗, 彭凌杰, 谢远昊, 等. 激光冲击强化对螺旋锥齿轮接触应力峰值的影响分析[J]. 塑性工程学报, 2025, 32(8): 210-220.
HE G Q, PENG L J, XIE Y H, et al.Influence Analysis of Laser Shock Peening on Peak Contact Stress of Spiral Bevel Gears[J]. Journal of Plasticity Engineering, 2025, 32(8): 210-220.
[21] 赵宁宁, 轩永辉, 胡岳银, 等. 激光强化地铁钢轨磨耗及滚动接触疲劳仿真研究[J]. 润滑与密封, 2026, 51(3): 124-131.
ZHAO N N, XUAN Y H, HU Y Y, et al.Simulation Study on Abrasion and Rolling Contact Fatigue of Laser- Enhanced Rails in Subways[J]. Lubrication Engineering, 2026, 51(3): 124-131.
[22] 杨俊茹, 徐昊, 王桂杰, 等. 基于Python的Abaqus二次开发在高温合金GH3039激光冲击强化中的应用[J]. 表面技术, 2023, 52(7): 435-443.
YANG J R, XU H, WANG G J, et al.Application of Python-Based Abaqus Redevelopment in Laser Shock Peening of Superalloy GH3039[J]. Surface Technology, 2023, 52(7): 435-443.
[23] 肖值兴, 毛建兴, 田腾跃, 等. 涡轮盘榫槽激光冲击强化数值模拟与试验验证[J]. 航空动力学报, 2022, 37(11): 2448-2454.
XIAO Z X, MAO J X, TIAN T Y, et al.Numerical Simulation and Experimental Verification on Laser Shock Peening for Turbine Mortise[J]. Journal of Aerospace Power, 2022, 37(11): 2448-2454.
[24] 张宇, 李潇, 贾先达, 等. ABAQUS二次开发的弧齿锥齿轮LTCA方法研究[J/OL]. 机械设计与制造, 1-8.
ZHANG Y, LI X, JIA X D, et al.Study on the LTCA Method for Spiral Bevel and Hypoid Gears Implemented through ABAQUS Secondary Development Platform[J/OL]. Machinery Design & Manufacture, 1-8.
[25] 蒋宗宏. 激光冲击强化对TC6钛合金力学性能影响[D]. 南昌: 南昌航空大学, 2024.
JIANG Z H.Effect of Laser Shock Peening on Mechanical Properties of TC6 Titanium Alloy[D]. Nanchang: Nanchang Hangkong University, 2024.
[26] LI J, GUO J T, LU W N, et al.Multiscale Simulation Combined with Experimental Investigation on Residual Stress and Microstructure of TC6 Titanium Alloy Treated by Laser Shock Peening[J]. Materials Today Communications, 2024, 40: 109484.
[27] FABBRO R, FOURNIER J, BALLARD P, et al.Physical Study of Laser-Produced Plasma in Confined Geometry[J]. Journal of Applied Physics, 1990, 68(2): 775-784.
[28] 朱然. 平顶光束多点激光冲击薄壁件的强化与变形研究[D]. 南京: 东南大学, 2019.
ZHU R.Study on Strengthening and Deformation of Thin- Walled Components under Flattened Beam Multiple Laser Shock Processing[D]. Nanjing: Southeast University, 2019.
[29] GORI F.Flattened Gaussian Beams[J]. Optics Communications, 1994, 107(5/6): 335-341.
[30] XU G, LU H F, LUO K Y, et al.Effects of Surface Curvature on Residual Stress Field of 316L Stainless Steel Subjected to Laser Shock Peening[J]. Optics & Laser Technology, 2021, 144: 107420.

基金

山东省科技厅重大创新工程项目(2022CXGC020703); 山东省自然科学基金(ZR2022ME150)

PDF(7312 KB)

Accesses

Citation

Detail

段落导航
相关文章

/

〈 〉