空心阴极放电复合Y2O3辅助离子渗碳对17CrNiMo6钢组织及性能的影响

李雨婷, 张润博, 董志宏, 辛丽, 鲍泽斌

表面技术 ›› 2026, Vol. 55 ›› Issue (21) : 169-178.

PDF(14698 KB)
PDF(14698 KB)
表面技术 ›› 2026, Vol. 55 ›› Issue (21) : 169-178. DOI: 10.16490/j.cnki.issn.1001-3660.2026.21.015
表界面强化技术

空心阴极放电复合Y2O3辅助离子渗碳对17CrNiMo6钢组织及性能的影响

  • 李雨婷1,2, 张润博3, 董志宏1,*, 辛丽1, 鲍泽斌1
作者信息 +

Effect of Plasma Carburizing Assisted by Hollow Cathode Discharge with Y2O3 on Microstructure and Properties of 17CrNiMo6 Steel

  • LI Yuting1,2, ZHANG Runbo3, DONG Zhihong1,*, XIN Li1, BAO Zebin1
Author information +
文章历史 +

摘要

目的 探究不同辅助工艺对17CrNiMo6钢离子渗碳层微观组织演变规律及摩擦学性能的影响机制,进而为其表面耐磨性的改善提供理论依据。方法 以17CrNiMo6 钢为基体,在900 ℃进行4 h的离子渗碳处理。试验共设置3个平行对照组,常规离子渗碳、空心阴极放电(Hollow Cathode Discharge,HCD)辅助离子渗碳以及HCD复合纳米Y2O3颗粒辅助离子渗碳。采用电子背散射衍射(EBSD)技术解析渗层物相组成与晶体学特征,利用光学显微镜(OM)、扫描电镜(SEM)及白光干涉技术表征其微观组织与磨痕三维形貌,并通过显微硬度测试与往复式摩擦磨损试验,系统评估不同工艺下渗碳层的力学性能与耐磨性。结果 渗碳后,3组试样的渗碳层均由马氏体、碳化物和残余奥氏体组成。HCD辅助明显提高了渗碳层中的碳浓度,使碳化物和残余奥氏体含量增加。引入钇元素后,碳化物和残余奥氏体的含量及形成深度进一步增加。HCD及其复合Y2O3辅助可加速碳原子扩散,增加有效硬化层厚度。HCD辅助时,有效硬化层厚度约为1.9 mm,较常规离子渗碳条件增加44%,HCD复合Y2O3辅助时为1.56 mm,增加18%。HCD辅助提高了渗碳层整体硬度,磨损率由常规离子渗碳时的2.34%减小至1.59%。当HCD复合Y2O3时,渗碳层表层硬度进一步提高,磨损率仅为0.26%。结论 HCD及其复合Y2O3辅助方法通过增强等离子体活性、促进碳扩散,可改善17CrNiMo6钢渗碳层组织形态,提高渗碳层的硬度、有效硬化层厚度以及摩擦磨损性能,为重载齿轮表面强化提供可行技术路径。

Abstract

The work aims to explore the effect of aid techniques used during plasma carburizing on the microstructure and characteristics of 17CrNiMo6 steel. 17CrNiMo6 steel was subjected to plasma carburizing at 900 ℃ for 4 h with the assistance of hollow cathode discharge (HCD) and rare earth oxide (Y2O3 nanoparticles). The impact of three carburizing treatments, namely standard plasma carburizing (PC), HCD-enhanced PC, and a hybrid HCD-PC process with Y2O3 doping, on the carburized microstructure and properties of 17CrNiMo6 steel was comprehensively examined. A comparative analysis was conducted with various advanced tools, ranging from microstructural observation (OM, SEM, and EBSD) and surface topography to phase identification (XRD). These structural changes were further correlated with the material's hardness and reciprocating wear resistance. The microstructure of the carburized layers in all three groups of samples was composed of martensite, carbides, and retained austenite. HCD assistance significantly increased the carbon concentration in the carburized layer, resulting in higher contents of carbides and retained austenite. After the addition of yttrium element, the content of carbide and retained austenite, as well as their formation depth, were further increased. HCD and its combination with Y2O3 were capable of accelerating carbon atom diffusion and increasing the thickness of the effective hardened layer. The effective hardened layer thickness reached 1.9 mm for PC with HCD, 44% higher than conventional PC. With the addition of Y2O3, the thickness was 1.56 mm, an increase of 18%. HCD assistance enhanced the hardness of the carburized layer, reducing the wear rate from 2.34% for conventional PC to 1.59%. When HCD was combined with Y2O3, the near-surface hardness of the carburized zone was further improved, yielding a wear rate of only 0.26%. Serving as a localized and intensified abnormal glow discharge, the hollow cathode effect (HCE) generated a highly concentrated plasma region within the cathode cavity. Integrating this phenomenon into the plasma carburizing system significantly elevated the effective carbon potential, thereby accelerating the carburization kinetics. Furthermore, the HCD-Y2O3 composite strategy activated the unique catalytic properties of rare earth elements, creating a robust synergistic enhancement coupled with the high-energy physical bombardment of HCD. This synergy was fundamentally attributed to the distinct electronic configuration and exceptional chemical reactivity of yttrium (Y) atoms under high-temperature plasma conditions. The intense ion bombardment of HCD stimulated Y2O3 to release yttrium element, which infiltrated into the steel surface and exerted an active element effect. Since the atomic radius of yttrium was larger than that of iron, yttrium infiltration induced lattice distortion, which raised the surface energy of the steel and enhanced the driving force for capturing active carbon atoms. Lattice distortion also increased the defect density, reduced the infiltration barrier for carbon atoms, and thus increased the carbon diffusion flux. Therefore, the carbon concentration gradient in the carburized layer was further elevated, allowing the austenite to be preserved to room temperature in deeper regions. The lattice distortion in the vicinity of yttrium atoms also led to carbon atoms aggregation, forming micro-regions with high carbon concentration. This not only facilitated the intragranular diffusion of carbon but also promoted the nucleation and rapid growth of carbides. In this work, Y2O3 particles are used as the rare earth source. Within the localized high-density plasma field generated by the hollow cathode, yttrium exhibits an accelerated binding affinity towards active carbon species, thereby significantly amplifying the intrinsic catalytic efficiency of the rare-earth element. The HCD and HCD-Y2O3 composite assistance methods optimize the microstructure morphology of the carburized layer of 17CrNiMo6 steel by enhancing plasma activity and promoting carbon diffusion, thereby improving the hardness, effective hardened layer thickness and friction and wear properties of the carburized layer. This offers a feasible technical solution for the surface strengthening of high-load gears.

关键词

17CrNiMo6钢 / 等离子体渗碳 / 空心阴极效应 / Y2O3颗粒 / 渗碳层 / 耐磨性

Key words

17CrNiMo6 steel / plasma carburizing / hollow cathode discharge / Y2O3 particles / carburized layer / friction and wear

引用本文

导出引用
李雨婷, 张润博, 董志宏, 辛丽, 鲍泽斌. 空心阴极放电复合Y2O3辅助离子渗碳对17CrNiMo6钢组织及性能的影响[J]. 表面技术. 2026, 55(21): 169-178
LI Yuting, ZHANG Runbo, DONG Zhihong, XIN Li, BAO Zebin. Effect of Plasma Carburizing Assisted by Hollow Cathode Discharge with Y2O3 on Microstructure and Properties of 17CrNiMo6 Steel[J]. Surface Technology. 2026, 55(21): 169-178
中图分类号: TG178   

参考文献

[1] 刘忠明. 中国战略性新兴产业研究与发展-齿轮, Gear: 齿轮 Gear[M]. 北京: 机械工业出版社, 2013.
LIU Z M.R&D of China’s Strategic New Industries[M]. Beijing: China Machine Press, 2013.
[2] 陈玲, 魏沛堂, 刘怀举, 等. 齿轮接触疲劳微观结构作用研究综述[J]. 机械传动, 2022, 46(1): 1-18.
CHEN L, WEI P T, LIU H J, et al.Review on the Effect of Microstructure on Gear Contact Fatigue[J]. Journal of Mechanical Transmission, 2022, 46(1): 1-18.
[3] MIAO S, WANG J G, JU D Y, et al.Improvement and Analysis of Fatigue Strength for Mild Steel 20MnCrS5 during Carburizing and Quenching[J]. Materials Science, 2020, 26(2): 192-198.
[4] JO B, SHARIFIMEHR S, SHIM Y, et al.Cyclic Deformation and Fatigue Behavior of Carburized Automotive Gear Steel and Predictions Including Multiaxial Stress States[J]. International Journal of Fatigue, 2017, 100: 454-465.
[5] WANG C Y, CHANG Y, LI X D, et al.Relation of Martensite-Retained Austenite and Its Effect on Microstructure and Mechanical Properties of the Quenched and Partitioned Steels[J]. Science China Technological Sciences, 2016, 59(5): 832-838.
[6] ZHANG K, ZHANG M H, GUO Z H, et al.A New Effect of Retained Austenite on Ductility Enhancement in High- Strength Quenching-Partitioning-Tempering Martensitic Steel[J]. Materials Science and Engineering: A, 2011, 528(29/30): 8486-8491.
[7] PANG Z R, YU S J, XU J W.Study of Effect of Quenching Deformation Influenced by 17CrNiMo6 Gear Shaft of Carburization[J]. Physics Procedia, 2013, 50: 103-112.
[8] SHI L, CUI X F, LI J, et al.Improving the Wear Resistance of Heavy-Duty Gear Steels by Cyclic Carburizing[J]. Tribology International, 2022, 171: 107576.
[9] 韩春阳, 胡寒婷, 张沛, 等. Nb微合金化17CrNiMo6钢齿轮轴的高温渗碳工艺[J]. 金属热处理, 2024, 49(11): 267-272.
HAN C Y, HU H T, ZHANG P, et al.High Temperature Carburizing Process of Nb Microalloyed 17CrNiMo6 Steel Gear Shaft[J]. Heat Treatment of Metals, 2024, 49(11): 267-272.
[10] YEROKHIN A L, NIE X, LEYLAND A, et al.Plasma Electrolysis for Surface Engineering[J]. Surface and Coatings Technology, 1999, 122(2/3): 73-93.
[11] DONG Z H, ZHANG W, KANG H W, et al.Surface Hardening of Laser Melting Deposited 12CrNi2 Alloy Steel by Enhanced Plasma Carburizing via Hollow Cathode Discharge[J]. Surface and Coatings Technology, 2020, 397: 125976.
[12] LIU H Y, CHE H L, LI G B, et al.Low-Pressure Hollow Cathode Plasma Source Carburizing Technique at Low Temperature[J]. Surface and Coatings Technology, 2021, 422: 127511.
[13] ZHANG Z H, WANG Z W, SHAO M H, et al.Nitrogen-Carbon-Induced Spinodal Structure in Plasma Nitrocarburized 38CrMoAl with Hollow Cathode Discharging[J]. Journal of Materials Science, 2024, 59(28): 13305-13322.
[14] DONG M L, CUI X F, ZHANG Y H, et al.Vacuum Carburization of 12Cr2Ni4A Low Carbon Alloy Steel with Lanthanum and Cerium Ion Implantation[J]. Journal of Rare Earths, 2017, 35(11): 1164-1170.
[15] KOLOBOV V I, METEL A S.Glow Discharges with Electrostatic Confinement of Fast Electrons[J]. Journal of Physics D: Applied Physics, 2015, 48(23): 233001.
[16] BARÁNKOVÁ H, BÁRDOŠ L, BERG S. The Radio Frequency Hollow Cathode Plasma Jet Arc for the Film Deposition[J]. Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films, 1996, 14(6): 3033-3038.
[17] MUHL S, PÉREZ A. The Use of Hollow Cathodes in Deposition Processes: A Critical Review[J]. Thin Solid Films, 2015, 579: 174-198.
[18] LI B Z, LI C S, LI Z X, et al.Microstructure and Mechanical Properties of Fe-Cr-2Ni-Mo-V Steel in Carburizing Process[J]. Procedia Manufacturing, 2018, 15: 1612-1618.
[19] HOSSAIN R, PAHLEVANI F, QUADIR M Z, et al.Stability of Retained Austenite in High Carbon Steel under Compressive Stress: An Investigation from Macro to Nano Scale[J]. Scientific Reports, 2016, 6: 34958.
[20] SHEN Y F, DONG X X, SONG X T, et al.Carbon Content-Tuned Martensite Transformation in Low-Alloy TRIP Steels[J]. Scientific Reports, 2019, 9: 7559.
[21] DONG Z H, CHEN S N, BAO Z B.Enhanced Plasma Nitriding Assisted by Combining Hollow Cathode Discharge with Rare Earth Oxide Particles for Iron-Based Metals[J]. Vacuum, 2024, 221: 112935.
[22] DONG M L, CUI X F, LU B W, et al.Accelerated Diffusion of Carbon and Grain Refinement of Vacuum Carburized Layer by La Ion Implantation[J]. Journal of Alloys and Compounds, 2020, 814: 152308.
[23] 刘志儒, 朱法义, 崔约贤, 等. 稀土低温高浓度渗碳表面渗层的微观组织[J]. 中国稀土学报, 1993, 11(3): 247-251.
LIU Z R, ZHU F Y, CUI Y X, et al.Microstructure of Surface Carburized Layer of Rare Earth at Low Temperature and High Concentration[J]. Journal of the Chinese Rare Earth Society, 1993, 11(3): 247-251.
[24] 刘志儒, 朱法义, 蔡成红, 等. 稀土低温高浓度气体渗碳工艺及其在20Cr2Ni4A钢上的应用[J]. 金属热处理, 1994, 19(11): 15-19.
LIU Z R, ZHU F Y, CAI C H, et al.High Carbon Concentration Carburizing Process at Low Temperature with Rare Earth Element and Its Application to Steel 20Cr2Ni4A[J]. Heat Treatment of Metals, 1994, 19(11): 15-19.
[25] LIU Z R, ZHU F Y, CUI Y X, et al.Microstructure of Surface Layer Formed at Low Temperature and High Carbon Concentration Carburizing with Rare Earth Element[J]. Journal of Rare Earths, 2006, 24(3): 363-367.
[26] HAGER C H, EVANS R D.Friction and Wear Properties of Black Oxide Surfaces in Rolling/Sliding Contacts[J]. Wear, 2015, 338: 221-231.
[27] ARUN PRAKASH N, BENNETT C J.The Effect of Plasma Nitriding and Post Oxidation on Fretting Wear Behaviour of a High Strength Alloy Steel[J]. Journal of Physics: Conference Series, 2017, 843: 012079.
[28] ABEDI H R, SALEHI M, YAZDKHASTI M.Novel Plasma Nitriding-Oxidizing Duplex Treatment of AISI 316 Austenitic Stainless Steel[J]. Materials Letters, 2010, 64(6): 698-701.
[29] SO H.The Mechanism of Oxidational Wear[J]. Wear, 1995, 184(2): 161-167.
[30] CONTE M, PINEDO B, IGARTUA A.Frictional Heating Calculation Based on Tailored Experimental Measurements[J]. Tribology International, 2014, 74: 1-6.

基金

中国辽宁省科学技术计划项目(2023JH1/10400052)

PDF(14698 KB)

Accesses

Citation

Detail

段落导航
相关文章

/

〈 〉