目的 研究柔性支撑参数对微珠自适应辅助摩擦电铸镍层表面完整性的影响趋势,分析海绵弹性系数与支撑间距对镍层表面形貌、组织结构和力学性能的影响。方法 在微珠自适应辅助摩擦电铸工艺下,以海绵弹性系数和支撑间距为变量制备电铸镍层,并结合表面粗糙度、SEM、力学性能和XRD残余应力进行表征。探讨柔性支撑参数对微珠自适应辅助摩擦电铸工艺所得镍层的影响。结果 柔性支撑参数对微珠自适应辅助摩擦工艺所制得的镍层影响显著。海绵弹性系数由0.15 N/mm增至0.20 N/mm时,电铸层的各项性能均得到提升,但海绵弹性系数继续提升至0.25 N/mm后,电铸层的各项性能变差。而支撑间距对电铸层的性能影响更为显著:4 mm支撑间距较0 mm支撑间距,镍层的表面粗糙度Ra低59.06%,显微硬度高48.66%,平均晶粒尺寸小52.79%,XRD结果显示镍层(111)晶面和(200)晶面的衍射峰强度相对更均衡,说明单一择优取向受到抑制,组织均匀性有所改善。结论 柔性支撑参数的作用主要与其对微珠法向约束、覆盖状态和持续摩擦条件的调节有关,从而影响机械整平、缺陷清除和机械活化作用;在各自单因素试验条件下,海绵弹性系数为0.20 N/mm、支撑间距为4 mm时分别表现较优,更有利于降低表面粗糙度、细化晶粒并减小残余应力。
Abstract
A self-adaptive microbead-assisted friction electroforming process was used to regulate the surface integrity of electroformed nickel by changing the structural parameters of the flexible support. Instead of relying on bath additives, this work introduced a sponge-supported zirconia microbead layer between the cathode core mold and the anode-side support. During pulse electroforming, the elastic support constrained the microbeads in the radial direction, while the rotating cathode drove continuous dynamic contact between the microbeads and the growing nickel surface. This configuration was designed to provide simultaneous mechanical leveling, removal of adsorbed gas bubbles and nodular defects, and mechanical activation of the deposition interface. Nickel layers were prepared in a nickel sulfamate electrolyte containing 400 g/L nickel sulfamate, 15 g/L nickel chloride, 30 g/L boric acid, and 0.05 g/L sodium dodecyl sulfate. The process was conducted at a current density of 3 A/dm2, a temperature of (43±1) ℃, pH=(4±0.1), a cathode rotation speed of 40 r/min, a pulse frequency of 1 500 Hz, and a duty cycle of 20%. Zirconia ceramic microbeads with diameters of 0.8-1.2 mm were used as the friction medium. Two single-factor parameter groups were examined: sponge elastic coefficients of 0.15, 0.20, and 0.25 N/mm, and support gaps of 0, 2, and 4 mm. The surface roughness, surface and fracture morphologies, tensile behavior, microhardness, crystallographic texture, grain size, and residual stress of the nickel layers were characterized by profilometry, SEM, tensile testing, microhardness testing, and XRD analysis. The results showed that the elastic coefficient of the sponge controlled the intensity and stability of microbead contact. When the elastic coefficient increased from 0.15 to 0.20 N/mm, the surface roughness decreased from 0.076 to 0.041 μm, the microhardness and tensile strength increased to 393.7HV and 930.2 MPa, respectively, the average grain size decreased to 25.49 nm, and the residual stress decreased to 89.8 MPa. Further increasing the elastic coefficient to 0.25 N/mm caused local indentation and scratch damage, accompanied by a reduction in strength and hardness and a partial increase in residual stress and grain size. These results indicated that excessive elastic constraint changed the microbead action from stable flexible friction to locally intensified contact, weakening the beneficial coupling between leveling and grain refinement. The support gap had an even more pronounced effect on the nickel layer. Increasing the gap from 0 to 4 mm reduced the surface roughness from 1.27 to 0.52 μm, increased the microhardness from 261.6 to 388.9HV, increased the tensile strength from 327.9 to 862.2 MPa, decreased the residual stress from 169.5 to 95.6 MPa, and refined the average grain size from 89.6 to 42.3 nm. XRD results further revealed that the dominant (200) texture observed at a gap of 0 mm gradually changed into a more balanced distribution of the (111) and (200) diffraction intensities as the gap increased, indicating suppression of single- orientation growth and improved microstructural uniformity. The fracture morphologies changed from uneven dimples and step-like fracture features to finer and more uniformly distributed dimples, confirming densification and grain refinement of the deposit. The mechanism is attributed to the regulation of the microbead coverage state, normal constraint, and movement freedom by the flexible support. An insufficient gap restricts microbead participation and weakens mechanical leveling and defect removal, whereas an appropriate gap allows more microbeads to participate in sustained friction, promotes nucleation, suppresses abnormal grain growth, and reduces local stress concentration. Under the present experimental conditions, a sponge elastic coefficient of 0.20 N/mm and a support gap of 4 mm are the favorable single-factor parameters for improving the surface integrity, microstructure, and mechanical properties of electroformed nickel.
关键词
电铸镍 /
柔性支撑 /
微珠自适应辅助摩擦 /
表面完整性 /
脉冲电铸
Key words
nickel electroforming /
flexible support /
self-adaptive microbead-assisted friction /
surface integrity /
pulse electroforming
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
参考文献
[1] 于峰, 刘凤娟, 张绪虎, 等. 液体火箭发动机推力室身部外壁快速电铸成型技术[J]. 导弹与航天运载技术, 2022(2): 98-103.
YU F, LIU F J, ZHANG X H, et al.The Rapid Electroforming Technology of Outer Wall for Liquid Rocket Engine Thrust Chamber[J]. Missiles and Space Vehicles, 2022(2): 98-103.
[2] SINGAM P, SPEEGLE C, MEEKHAM A, et al.Optimizing the Electroforming Process for Full-Shell X-Ray Optics[J]. Journal of Astronomical Telescopes, Instruments, and Systems, 2024, 10(3): 034001.
[3] CHEN T Y, MA Y Q, HUANG Q M, et al.Preparation and Characterization of High Electrical Conductivity and Corrosion Resistant Black Passivation Film on Zn-Ni Alloy Coating of AA2024 Substrates[J]. Journal of Alloys and Compounds, 2026, 1051: 185976.
[4] WANG Z Z, SHEN C J, MA Z, et al.A Nickel Dissolution Process for Multilayer Electroforming to Achieve Ultrahigh Adhesion Strength[J]. Materials, 2023, 16(19): 6504.
[5] GUO B J, DU L Q, WANG S, et al.Enhancement of Micro Hole Wetting and Hydrogen Bubble Release in the Process of Ni Micro Electroforming under Megasonic Field[J]. Surfaces and Interfaces, 2024, 44: 103762.
[6] ZHANG L, YANG D, MA Z G, et al.Pulse Current Electroforming of Ni-PTFE Nanocomposite Mold Insert with Long-Lifetime and Anti-Adhesive Properties[J]. Electrochimica Acta, 2024, 491: 144308.
[7] SIVASUBRAMANIAN J, UPADHYAY P, MALLIK A, et al.Electrochemical Corrosion Behaviour of Electrodeposited Nickel Coating Subjected to Ultrasonic Shot Peening Treatment[J]. Surface and Coatings Technology, 2025, 503: 132005.
[8] 钱王欢, 王松雷, 周丽, 等. 垂直冲液辅助对镍-氧化铈复合电铸层微观结构的影响[J]. 电镀与涂饰, 2023, 42(1): 18-23.
QIAN W H, WANG S L, ZHOU L, et al.Effect of the Assistance of Vertical Flushing during Electroforming on Microstructure of Ni-CeO2 Composite Coating[J]. Electroplating & Finishing, 2023, 42(1): 18-23.
[9] YANG X H, ZHANG X M, MING P M, et al.Fabricating Ultra-Narrow Precision Slit Structures with Periodically Reducing Current Over-Growth Electroforming[J]. Micromachines, 2024, 15(1): 76.
[10] QIAN S Q, SHAO W Y, ZHAO Y F, et al.Improving Uniformity and Performance of Electroformed Copper Using Rare Earth Element Additives[J]. International Journal of Electrochemical Science, 2024, 19(5): 100549.
[11] TAMBE C E, GREEN T A, ROY S.The Multifaceted Role of Boric Acid in Nickel Electrodeposition and Electroforming[J]. Journal of the Electrochemical Society, 2024, 171(10): 102503.
[12] QIANG J, JIANG B Y, DONG Y Z, et al.Tuning Residual Stress in Electrodeposited Nickel Films via Pulse Current[J]. Surfaces and Interfaces, 2023, 40: 103038.
[13] YAMAMOTO T, IGAWA K, TANG H, et al.Effects of Current Density on Mechanical Properties of Electroplated Nickel with High Speed Sulfamate Bath[J]. Microelectronic Engineering, 2019, 213: 18-23.
[14] SHEN C J, ZHU Z W, ZHU D, et al.Copper Deposits with High Tensile Strength and Elongation Electroformed in an Ultra-Low-Concentration Sulfate Bath without Additives[J]. Journal of Materials Engineering and Performance, 2017, 26(3): 987-992.
[15] ZHU Z W, ZHU D, QU N S, et al.Electroforming of Revolving Parts with Near-Polished Surface and Uniform Thickness[J]. The International Journal of Advanced Manufacturing Technology, 2008, 39(11): 1164-1170.
[16] 章勇, 朱增伟, 朱荻. 柔性摩擦辅助电铸新技术的研究[J]. 中国机械工程, 2012, 23(8): 893-896.
ZHANG Y, ZHU Z W, ZHU D.Study on New Technology of Electroforming with Flexible Friction[J]. China Mechanical Engineering, 2012, 23(8): 893-896.
[17] LV B, HU Z F, WANG X H, et al.Electrodeposition of Nanocrystalline Nickel Assisted by Flexible Friction from an Additive-Free Watts Bath[J]. Surface and Coatings Technology, 2015, 270: 123-131.
[18] LIU X, SHEN L D, QIU M B, et al.Jet Electrodeposition of Nanocrystalline Nickel Assisted by Controllable Friction[J]. Surface and Coatings Technology, 2016, 305: 231-240.
[19] REN J H, ZHU Z W, XIA C Q, et al.Abrasive-Assisted Nickel Electroforming Process with Moving Cathode[J]. Chinese Journal of Mechanical Engineering, 2017, 30(2): 294-300.
[20] 钱王欢, 秦丰, 缪小梅. 柔性受压电铸新技术研究[J]. 中国机械工程, 2016, 27(22): 3001-3004.
QIAN W H, QIN F, MIAO X M.Novel Technique for Electroforming with Flexible Compression[J]. China Mechanical Engineering, 2016, 27(22): 3001-3004.
[21] ZHUO W, SHEN L D, QIU M B, et al.Effects of Flexible Friction on the Properties of Nanocrystalline Nickel Prepared by Jet Electrodeposition[J]. Surface and Coatings Technology, 2018, 333: 87-95.
[22] 姚传慧, 任建华, 尹冠华, 等. 微珠柔性受压辅助磨电铸镍工艺[J]. 电镀与涂饰, 2023, 42(9): 24-30.
YAO C H, REN J H, YIN G H, et al.Nickel Electroforming Assisted by Friction of Micro-Beads under Flexible Compression[J]. Electroplating & Finishing, 2023, 42(9): 24-30.
[23] JI F, QIAN S Q, SHAO W Y, et al.The Effect of Microbead Fusion Flexible Friction-Assisted Electroforming on the Surface Roughness of Electroformed Layers[J]. Coatings, 2025, 15(11): 1250.
[24] 董迎港, 任建华, 周超, 等. 脉冲参数对微珠自适应辅助磨脉冲电铸镍性能的影响[J]. 表面技术, 2025, 54(10): 246-255.
DONG Y G, REN J H, ZHOU C, et al.Effect of Pulse Parameters on Properties of Pulse Electroforming Nickel by Microbead Adaptive Assisted Grinding[J]. Surface Technology, 2025, 54(10): 246-255.
[25] 李学磊, 朱荻, 朱增伟. 游离粒子对摩擦辅助电铸技术的影响[J]. 电加工与模具, 2010(4): 35-39.
LI X L, ZHU D, ZHU Z W.Effect of Free Particles to the Abrasion-Assisted Electroforming Technique[J]. Electromachining & Mould, 2010(4): 35-39.
[26] HU J C, ZHU Z W.Homogeneous Nanocrystalline Ni-Co Alloys with Excellent Mechanical Properties via Abrasive- Assisted Electroforming[J]. Journal of Materials Science, 2023, 58(22): 9349-9361.
[27] YIN G H, REN J H, WANG Z X, et al.Investigation of the Tensile Properties of Friction-Assisted Electroforming Copper with Free Beads[J]. Journal of Materials Engineering and Performance, 2024, 33(18): 9676-9685.