Ti-6Al-4V表面Mo改性层的制备及梯度力学性能分析

李达, 王靖伟, 赵功奥, 贾宜委, 邱吉, 王鹤峰

表面技术 ›› 2026, Vol. 55 ›› Issue (21) : 137-148.

PDF(5225 KB)
PDF(5225 KB)
表面技术 ›› 2026, Vol. 55 ›› Issue (21) : 137-148. DOI: 10.16490/j.cnki.issn.1001-3660.2026.21.012
表界面强化技术

Ti-6Al-4V表面Mo改性层的制备及梯度力学性能分析

  • 李达1, 王靖伟2, 赵功奥1, 贾宜委1, 邱吉1, 王鹤峰1,3,*
作者信息 +

Preparation of Mo-modified Layer on Ti-6Al-4V Surface and Analysis of Gradient Mechanical Properties

  • LI Da1, WANG Jingwei2, ZHAO Gongao1, JIA Yiwei1, QIU Ji1, WANG Hefeng1,3,*
Author information +
文章历史 +

摘要

目的 解决Ti-6Al-4V(TC4)钛合金在实际应用中硬度低和耐磨性差的问题。方法 采用双辉等离子表面合金化技术(DGPSA)在TC4钛合金表面制备了钼(Mo)改性层,利用SEM、EDS和EBSD对其形貌、晶体结构进行表征。沿改性层截面按点阵排布方式布置压痕点位(覆盖沉积层、扩散层和基体),采用连续刚度法进行纳米压痕测试来探究改性层梯度力学性能。结果 制备的Mo改性层内部致密均匀,沉积层厚度约13 μm,硬度和弹性模量分别为11.5 GPa和220 GPa,Mo原子呈现出细晶结构;扩散层厚度约8 μm,硬度为5.5~12.5 GPa,弹性模量为131~217 GPa,出现了Ti和Mo的混合相(如Mo9Ti4)。结论 沉积层硬度和模量高且分布均匀,主要源于Mo的高本征力学性能和细晶强化机制;扩散层硬度和模量呈梯度下降,强化机制为固溶强化与弥散强化的协同效应,在扩散层初期出现硬度峰值。

Abstract

A Mo-modified layer was prepared on a TC4 titanium alloy substrate using the double glow plasma surface alloying (DGPSA) technology to improve the inherent performance deficiencies of the alloy, such as low surface hardness and poor wear resistance. To address the limitation of conventional surface nanoindentation tests in obtaining the evolution of mechanical properties along the depth direction of the modified layer, a cross-sectional nanoindentation grid testing scheme was designed to systematically characterize the gradient mechanical properties of the modified layer along its thickness.
TC4 substrates were machined by wire cutting into specimens measuring 10 mm×5 mm ×5 mm, sequentially ground with SiC sandpapers from 400# to 2000#, and then polished with diamond polishing paste to a mirror finish. High-purity molybdenum plates were used as the source electrode material. The DGPSA process parameters were: source voltage 800 V, cathode voltage 550 V, working gas pressure 30 Pa, processing temperature (800±5) ℃, holding time 4 h, with a fixed distance of 15 mm between the source and the cathode. The microstructure of the modified layer was characterized with a scanning electron microscope (SEM) equipped with an energy dispersive spectrometer (EDS) and electron backscatter diffraction (EBSD). Nanoindentation point arrays with 2 μm spacing were arranged along the specimen cross section, covering the deposited layer, diffusion layer, and substrate regions. Nanoindentation tests were conducted with the Nano Indenter G200 system through continuous stiffness measurement (CSM), with a maximum penetration depth set to 500 nm.
The prepared Mo-modified layer had a dense structure and uniform organization, with a total thickness of approximately 21 μm, which could be distinctly divided into the deposited layer (about 13 μm) and the diffusion layer (about 8 μm). EBSD analysis results indicated that the deposited layer was mainly composed of pure Mo, with fine grains and random orientation distribution. In the diffusion layer, the Mo content gradually decreased in a continuous gradient from the deposited layer interface toward the substrate, forming a novel hard intermetallic phase Mo9Ti4, which was uniformly dispersed within the diffusion layer. Nanoindentation test results showed that the modified layer exhibited significant gradient mechanical properties along the depth direction: the deposited layer showed high and stable hardness (11.5 GPa) and elastic modulus (220 GPa); within the diffusion layer, hardness and elastic modulus exhibited a continuous gradient decrease from the deposited layer side toward the substrate side. Notably, in the initial region of the diffusion layer, the hardness reached a maximum value of 12.5 GPa, higher than that of the deposited layer. This peak hardness was attributed to the synergistic effects of solid solution strengthening and dispersion strengthening: Mo atoms dissolved in the β-Ti lattice induce lattice distortion, while the uniformly dispersed Mo9Ti4 hard phase effectively hindered dislocation movement. As the depth of the diffusion layer increased, the Mo content gradually decreased, and both strengthening effects were simultaneously weakened, reducing the hardness and elastic modulus to 5.5 GPa and 131 GPa, respectively, at the diffusion layer-substrate interface. The load-displacement curves of the diffusion layer exhibited higher dispersion than those of the deposited layer, reflecting the non-uniformity of the compositional distribution in the interdiffusion region; however, no interfacial cracking or delamination was observed in the indentation morphology, indicating that the diffusion layer acted as a stress-buffering layer, effectively coordinating the mechanical mismatch between the hard deposited layer and the relatively soft substrate.
The high-hardness deposited layer gives the modified layer excellent wear resistance, while the gradient diffusion layer ensures interfacial bonding strength, allowing the modified layer to have good application potential under service conditions that require both surface durability and structural integrity. In this study, a set of quantitative experimental methods for characterizing the mechanical properties of gradient-modified layers is established through cross-sectional nanoindentation testing.

关键词

表面改性 / 改性层形成机理 / 梯度力学性能 / 纳米压痕 / 双辉等离子合金化技术 / Ti-6Al-4V合金

Key words

surface modification / mechanism of modified layer formation / gradient mechanical properties / nanoindentation / double glow plasma surface alloying / Ti-6Al-4V alloy

引用本文

导出引用
李达, 王靖伟, 赵功奥, 贾宜委, 邱吉, 王鹤峰. Ti-6Al-4V表面Mo改性层的制备及梯度力学性能分析[J]. 表面技术. 2026, 55(21): 137-148
LI Da, WANG Jingwei, ZHAO Gongao, JIA Yiwei, QIU Ji, WANG Hefeng. Preparation of Mo-modified Layer on Ti-6Al-4V Surface and Analysis of Gradient Mechanical Properties[J]. Surface Technology. 2026, 55(21): 137-148
中图分类号: TG174.445   

参考文献

[1] QIN L, LIU C S, YANG K K, et al.Characteristics and Wear Performance of Borided Ti6Al4V Alloy Prepared by Double Glow Plasma Surface Alloying[J]. Surface and Coatings Technology, 2013, 225: 92-96.
[2] WEI D B, ZHANG P Z, YAO Z J, et al.Double Glow Plasma Chromizing of Ti6Al4V Alloys: Impact of Working Time, Substrate-Target Distance, Argon Pressure and Surface Temperature of Substrate[J]. Vacuum, 2015, 121: 81-87.
[3] REN Z Y, HU Y L, TONG Y G, et al.Wear-Resistant NbMoTaWTi High Entropy Alloy Coating Prepared by Laser Cladding on TC4 Titanium Alloy[J]. Tribology International, 2023, 182: 108366.
[4] JIANG Z G, ZHENG Q Y, YUAN Z P, et al.Achieving Dual Strengthening in Plasma-Sprayed Mo Coatings via Acoustic-Electro-Stress Synergistic Processing: Microstructural Micro-Forging and Interfacial Micro-Metallurgy[J]. Surface and Coatings Technology, 2025, 514: 132593.
[5] 刘猛, 白书欣, 李顺, 等. SiC颗粒表面Mo涂层的制备与分析[J]. 稀有金属材料与工程, 2016, 45(4): 1072-1077.
LIU M, BAI S X, LI S, et al.Preparation and Analysis of Molybdenum Coating on the Surface of Silicon Carbide[J]. Rare Metal Materials and Engineering, 2016, 45(4): 1072-1077.
[6] 赵劲凯, 汪洪, 贾金升, 等. 金属涂层光纤制备方法与性能研究进展[J]. 硅酸盐通报, 2022, 41(11): 3745-3755.
ZHAO J K, WANG H, JIA J S, et al.Research Progress on Preparation Method and Property ofMetal Coated Optical Fibers[J]. Bulletin of the Chinese Ceramic Society, 2022, 41(11): 3745-3755.
[7] 杨嘉乐, 徐立新, 李东山, 等. 微弧预氧化对Ti6Al4V钛合金低温等离子体氮化层耐磨耐蚀性的影响[J]. 材料保护, 2025, 58(6): 102-115.
YANG J L, XU L X, LI D S, et al.Effect of Micro-Arc Pre-Oxidation on Wear and Corrosion Resistance of Low-Temperature Plasma Nitrided Layer on Ti6Al4V Titanium Alloy[J]. Materials Protection, 2025, 58(6): 102-115.
[8] 赵慧敏, 李昆达, 班美丽, 等. 钛合金表面二氧化锆/羟基磷灰石涂层的制备及性能研究[J]. 热加工工艺, 2025, 54(12): 150-154.
ZHAO H M, LI K D, BAN M L, et al.Research on Preparation and Properties of Zirconia/Hydroxyapatite Coating on Titanium Alloy Surface[J]. Hot Working Technology, 2025, 54(12): 150-154.
[9] 胡巍, 梁文萍. TC4钛合金的双辉等离子渗氮[J]. 热处理, 2021, 36(2): 7-13.
HU W, LIANG W P.Double Glow Plasma Nitriding of TC4 Titanium Alloy[J]. Heat Treatment, 2021, 36(2): 7-13.
[10] TAN X Y, CHEN G B, TEO S L, et al.Substrate Dilution and Interface Structures of Tungsten Coating Deposited by Double-Glow Plasma Surface Alloying on Stainless Steel Substrate[J]. Surface and Coatings Technology, 2024, 489: 131153.
[11] WEI D B, ZHANG P Z, YAO Z J, et al.Double Glow Plasma Chromizing of Ti6Al4V Alloys: Impact of Working Time, Substrate-Target Distance, Argon Pressure and Surface Temperature of Substrate[J]. Vacuum, 2015, 121: 81-87.
[12] 王振霞, 王文波, 贺志勇, 等. 钛(TA2)及钛合金(TC4)表面等离子渗Nb研究[J]. 热加工工艺, 2005, 34(9): 1-2.
WANG Z X, WANG W B, HE Z Y, et al.Study of Plasma Niobium Surface Alloying on Titanium(TA2) and Titanium Alloys(TC4)[J]. Hot Working Technology, 2005, 34(9): 1-2.
[13] 魏东博, 李民锋, 刘希琴, 等. 表面等离子W-Mo合金化对粉末冶金齿轮组织成分及耐磨性能的影响[J]. 表面技术, 2021, 50(1): 305-312.
WEI D B, LI M F, LIU X Q, et al.Effect of Surface Plasma W-Mo Alloying on Microstructure and Wear Resistance of Powder Metallurgy Gears[J]. Surface Technology, 2021, 50(1): 305-312.
[14] 龚江宏. 准静态纳米压痕的理论基础与数据分析[J]. 陶瓷学报, 2021, 42(2): 181-245.
GONG J H.Theoretical Foundation and Data Analyses of Quasi-Static Nanoindentation[J]. Journal of Ceramics, 2021, 42(2): 181-245.
[15] 陈利, 汪秀全, 尹飞, 等. TiN涂层的微观组织结构及力学性能分析[J]. 硬质合金, 2006, 23(1): 8-10.
CHEN L, WANG X Q, YIN F, et al.Research on Microstructure and Mechanical Properties of TiN Coating[J]. Cemented Carbide, 2006, 23(1): 8-10.
[16] 郑康培, 刘平, 李伟, 等. Al含量对CrAlN涂层微观结构和力学性能的影响[J]. 真空科学与技术学报, 2011, 31(6): 686-690.
ZHENG K P, LIU P, LI W, et al.Impacts of Al Content on Microstructures and Mechanical Properties of CrAlN Coatings[J]. Chinese Journal of Vacuum Science and Technology, 2011, 31(6): 686-690.
[17] BRECHELT S, WICHE H, JUNGE J, et al.Diffusion Barriers for Electrodes in Resistance Spot Welding of Aluminum Alloys—Investigation of Coating Characteristics Using Nanoindentation and SEM Analysis[J]. Surfaces, 2025, 8(4): 81.
[18] HARTLEB M, IMRICH P, ZECHNER J, et al.Adhesion Properties of Polyimide Coated Stacks: An In-Depth Analysis of the Cross-Sectional Nanoindentation Method[J]. Heliyon, 2024, 10(24): e40967.
[19] 梁立红, 刘海燕, 宋晶如, 等. 先进涂层体系的跨尺度硬度及界面梯度效应研究[J]. 中国材料进展, 2020, 39(10): 723-727.
LIANG L H, LIU H Y, SONG J R, et al.Investigation on Trans-Scale Hardness and Interface Gradient Effect of Advanced Coating System[J]. Materials China, 2020, 39(10): 723-727.
[20] 曾华智, 王海, 沈军. 梯度基体负偏压真空多弧离子镀沉积TiN涂层及其力学性能[J]. 表面技术, 2016, 45(2): 79-83.
ZENG H Z, WANG H, SHEN J.Arc Ion Plating with Gradient Bias Voltage Deposition and Mechanical Properties of TiN Coatings[J]. Surface Technology, 2016, 45(2): 79-83.
[21] WANG Y D, WANG H F, JIA Y W, et al.Nano- Mechanical Properties of Mo Coating Prepared on Invar Alloy Substrate by Double Glow Plasma Surface Alloying[J]. Surface and Coatings Technology, 2022, 447: 128850.
[22] 贾宜委. TC4钛合金表面CoCrFeNiMn改性层制备及力学性能研究[D]. 太原: 太原理工大学, 2024.
JIA Y W.Preparation and Mechanical Properties of CoCrFeNiMn Modified Layer on TC4 Titanium Alloy Surface[D]. Taiyuan: Taiyuan University of Technology, 2024.
[23] YANG H B, LI X, WANG Q, et al.Effects of Coiling Temperature on the Microstructure and Mechanical Response of Ti-Mo Micro-Alloyed Steel[J]. Journal of Materials Engineering and Performance, 2026, 35(27): 27633-27642.
[24] 陈忠兵, 孙志强, 杨佳, 等. 基于梯度过渡的铁基合金涂层组织与性能研究[J]. 焊接技术, 2024, 53(5): 50-54.
CHEN Z B, SUN Z Q, YANG J, et al.Research on the Structure and Performance of Iron-Based Alloy Coating Based on Gradient Transition[J]. Welding Technology, 2024, 53(5): 50-54.
[25] OLIVEIRA J P, PONDER K, BRIZES E, et al.Combining Resistance Spot Welding and Friction Element Welding for Dissimilar Joining of Aluminum to High Strength Steels[J]. Journal of Materials Processing Technology, 2019, 273: 116192.
[26] WANG L B, CHEN Z F, ZHANG P Z, et al.Ir Coating Prepared on Mo Substrate by Double Glow Plasma[J]. Journal of Coatings Technology and Research, 2009, 6(4): 517-522.
[27] 魏春肖, 陈杉杉, 范荣奎, 等. 相图分析在二元钼合金中的应用[J]. 中国钼业, 2019, 43(2): 48-51.
WEI C X, CHEN S S, FAN R K, et al.Application of Phase Diagram in the Binary Alloying Process of Molybdenum[J]. China Molybdenum Industry, 2019, 43(2): 48-51.
[28] KOSTIN V A, BERDNIKOVA O M, et al.Structure and Properties of Sparsely-Alloyed Ti-2.8Al-5.1Mo-4.9Fe[J]. Electrometallurgy Today, 2022(2): 39-49.
[29] 蒋淑英, 李世春. Al/Ti液/固界面扩散溶解层形成机制及生长规律[J]. 稀有金属材料与工程, 2011, 40(6): 983-986.
JIANG S Y, LI S C.Formation Mechanism and Growth Law of Diffusion Solution Zone between Al/Ti Liquid/Solid Interface[J]. Rare Metal Materials and Engineering, 2011, 40(6): 983-986.
[30] 孙达, 李顺朴. Al膜和衬底Ti间的反应和互扩散[J]. 兰州大学学报, 1993, 29(1): 42-47.
SUN D, LI S P.Reactions and Interdiffusions between Al Film and Substrate Ti[J]. Journal of Lanzhou University, 1993, 29(1): 42-47.
[31] TARASOVA T, VOLOSOVA M, SKOROBOGATOV A, et al.Investigation of the Structure and Properties of Molybdenum Coatings Produced by Laser-Directed Energy Deposition[J]. Coatings, 2023, 13(8): 1365.
[32] 杨曌. 钛合金Mo梯度改性层多尺度力学性能的研究[D]. 太原: 太原理工大学, 2020.
YANG Z.Multi-scale Mechanical Properties of Mo Gradient Modified Layer of Titanium Alloy[D]. Taiyuan: Taiyuan University of Technology, 2020.
[33] 刘亚楠, 谷米, 孙荣禄, 等. 钛合金表面激光熔覆原位制备TiC/Ti2Ni复合涂层微观组织及性能研究[J]. 中国激光, 2021, 48(14): 115-125.
LIU Y N, GU M, SUN R L, et al.Microstructure and Properties of In-Situ TiC/Ti2Ni Composite Coating Prepared via Laser Cladding on Titanium Alloy[J]. Chinese Journal of Lasers, 2021, 48(14): 115-125.
[34] 郭海霞, 梁成浩, 牟宗信. 离子注入TiNiSMA及Co合金耐蚀性与血液相容性研究[J]. 大连理工大学学报, 2002, 42(3): 301-305.
GUO H X, LIANG C H, MU Z X.Study of Corrosion Behavior and Haemocompatibility of Ion-Implanted TiNi Shape Memory Alloy and Cobalt Alloys[J]. Journal of Dalian University of Technology, 2002, 42(3): 301-305.
[35] 秦亚东, 高方圆, 许亿, 等. HiPIMS溅射AlCrN涂层结构对抗铝黏着性能的影响[J]. 中国表面工程, 2025, 38(1): 216-227.
QIN Y D, GAO F Y, XU Y, et al.Effect of HiPIMS Sputtered AlCrN Coating Structures on Anti-Aluminum Adhesion Properties[J]. China Surface Engineering, 2025, 38(1): 216-227.

基金

国家自然科学基金青年科学基金项目(12302477)

PDF(5225 KB)

Accesses

Citation

Detail

段落导航
相关文章

/

〈 〉