目的 探明调制周期对高功率脉冲磁控溅射(HiPIMS)制备Nb/NbN多层涂层组织、膜基结合力、耐蚀导电性能的影响,为质子交换膜燃料电池金属双极板涂层结构优化提供依据。方法 在316L不锈钢和Si表面制备总沉积时间相同、调制周期不同的C1、C2和C3涂层,采用SEM、激光共聚焦显微镜、GI-XRD及XPS表征涂层的组织及成分,并通过划痕—EDS测试、电化学及ICR测试评价涂层的性能。结果 3组涂层厚度为352~365 nm,调制周期分别为365、178.5、70.4 nm,均由体心立方Nb与立方NbN相组成,表面粗糙度基本一致;随着调制周期减小,柱状晶连续生长受到抑制,Nb(110)衍射峰逐渐减弱;C2和C3涂层的膜基结合力分别达到8.5、8.3 N,明显高于C1涂层的0.9 N;涂层样品耐腐蚀性能显著优于316L不锈钢基体,其中C3的动电位腐蚀电流密度最低,为3.956 5×10‒8 A/cm2,电荷转移电阻最高,为2.006×106 Ω·cm2;C2在恒电位测试0.60和1.36 V(vs. SCE)下平均稳态电流密度最低;在1.4 MPa下,3组涂层ICR均低于2.400 mΩ·cm2,C1最低,为1.987 mΩ·cm2。结论 与单调制周期的C1涂层相比,C2和C3的膜基结合力及耐蚀性明显提高。减小调制周期有利于抑制柱状生长、增强腐蚀阻隔能力,但过多界面会削弱连续Nb导电通道并增加电子散射。C2兼顾膜基结合力、耐蚀性和导电性,为本实验条件下综合性能最优的结构方案。
Abstract
The work aims to elucidate the effects of modulation period on the microstructural evolution, coating-substrate adhesion, corrosion resistance, and interfacial electrical conductivity of Nb/NbN multilayer coatings prepared by high-power impulse magnetron sputtering (HiPIMS), thereby providing a basis for the structural optimization of metallic bipolar plate coatings for proton exchange membrane fuel cells (PEMFCs). Nb/NbN multilayer coatings were deposited on 316L stainless steel and n-type monocrystalline (111) silicon substrates with identical total deposition time. Three groups of coatings (denoted as C1, C2 and C3) were prepared by adjusting the deposition duration of Nb and NbN sublayers in one modulation cycle, with sublayer time settings of 30 min/30 min, (15 min/15 min)×2 and (6 min/6 min)×5, respectively. Scanning electron microscopy (SEM), laser confocal microscopy, grazing-incidence X-ray diffraction (GI-XRD), X-ray photoelectron spectroscopy (XPS), and scratch testing combined with energy-dispersive X-ray spectroscopy (EDS) were used to characterize the microstructure, surface roughness, phase composition, chemical states, and coating-substrate adhesion. Potentiodynamic polarization, potentiostatic polarization, EIS, and ICR measurements were employed to evaluate corrosion resistance and interfacial electrical conductivity. The three coatings had similar thicknesses of approximately 352-365 nm, with modulation periods of 365, 178.5 and 70.4 nm for C1, C2 and C3, respectively. All coatings exhibited continuous and dense columnar microstructures in cross-section and consisted of body-centered cubic Nb and cubic NbN phases. With the decreasing modulation period, the grains became progressively finer, the continuous growth of columnar crystals was inhibited, and the intensity of the Nb(110) diffraction peak gradually decreased. The Nb/NbN multilayer coatings showed significantly better corrosion resistance than the 316L stainless steel substrate, and the performance of C2 and C3 was remarkably improved compared with C1. The C3 coating achieved the lowest potentiodynamic corrosion current density of 3.956 5×10-8 A/cm2 and the highest charge transfer resistance of 2.006× 106 Ω·cm2. In contrast, the C2 coating presented the lowest average steady-state current density under potentiostatic polarization at 0.60 and 1.36 V (vs. SCE), which are 32.26×10-9 A/cm2 and 3.186×10-6 A/cm2, respectively, showing superior long-term stability under simulated fuel cell operating conditions. For electrical conductivity, the Nb/NbN multilayer coatings significantly improved the electrical conductivity of 316L stainless steel. All three coatings had ICR values lower than 2.4 mΩ·cm2, among which C1 obtained the minimum ICR of 1.987 5 mΩ·cm2 at a compaction pressure of 1.4 MPa. It is concluded that Nb/NbN multilayer coatings can simultaneously enhance the corrosion resistance and interfacial conductivity of 316L stainless steel. Compared with the single-period C1 coating, the coating-substrate adhesion of C2 and C3 is substantially improved, demonstrating that reducing the modulation period and increasing the number of heterogeneous interfaces can effectively interrupt the continuous propagation of columnar structures and cracks, thereby enhancing adhesion stability and resistance to spallation. Reducing the modulation period strengthens the barrier effect of the coating by increasing interfacial density and blocking corrosion paths, but excessive interfaces will impair the integrity of continuous Nb conductive channels and aggravate electron scattering at interfaces and defects. Considering coating-substrate adhesion, corrosion resistance, and the balance between electrical conductivity and corrosion resistance, the C2 coating with a modulation period of 178.5 nm exhibits the optimal overall performance under the experimental conditions.
关键词
Nb/NbN多层涂层 /
高功率脉冲磁控溅射 /
调制周期 /
燃料电池双极板 /
耐腐蚀性能 /
接触电阻
Key words
Nb/NbN multilayer coating /
HiPIMS /
modulation period /
fuel cell bipolar plate /
corrosion resistance /
interfacial contact resistance
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
参考文献
[1] WANG Y, CHEN K S, MISHLER J, et al.A Review of Polymer Electrolyte Membrane Fuel Cells: Technology, Applications, and Needs on Fundamental Research[J]. Applied Energy, 2011, 88(4): 981-1007.
[2] ANTUNES R A, OLIVEIRA M C L, ETT G, et al. Corrosion of Metal Bipolar Plates for PEM Fuel Cells: A Review[J]. International Journal of Hydrogen Energy, 2010, 35(8): 3632-3647.
[3] TAWFIK H, HUNG Y, MAHAJAN D.Metal Bipolar Plates for PEM Fuel Cell: A Review[J]. Journal of Power Sources, 2007, 163(2): 755-767.
[4] 李伟, 李争显, 刘林涛, 等. 质子交换膜燃料电池金属双极板表面改性研究进展[J]. 表面技术, 2018, 47(10): 81-89.
LI W, LI Z X, LIU L T, et al.Research Progress on Surface Modification of Metal Bipolar Plate for Proton Exchange Membrane Fuel Cell[J]. Surface Technology, 2018, 47(10): 81-89.
[5] 孙贤伟, 李希超, 赵经香, 等. 质子交换膜燃料电池双极板防护涂层研究进展[J]. 表面技术, 2023, 52(5): 26-36.
SUN X W, LI X C, ZHAO J X, et al.Research Progress on Protective Coatings for Bipolar Plates of Proton Exchange Membrane Fuel Cells[J]. Surface Technology, 2023, 52(5): 26-36.
[6] 陈栋, 党博, 杨凯, 等. 过渡金属氮化物PEMFC双极板涂层研究进展[J]. 表面技术, 2025, 54(3): 39-61.
CHEN D, DANG B, YANG K, et al.Research Progress of Transition Metal Nitride Coatings on PEMFC Metal Bipolar Plate[J]. Surface Technology, 2025, 54(3): 39-61.
[7] ZHANG H B, LIN G Q, HOU M, et al.CrN/Cr Multilayer Coating on 316L Stainless Steel as Bipolar Plates for Proton Exchange Membrane Fuel Cells[J]. Journal of Power Sources, 2012, 198: 176-181.
[8] ATAPOUR M, RAJAEI V, TRASATTI S, et al.Thin Niobium and Niobium Nitride PVD Coatings on AISI 304 Stainless Steel as Bipolar Plates for PEMFCs[J]. Coatings, 2020, 10(9): 889.
[9] BARSHILIA H C, SURYA PRAKASH M, POOJARI A, et al.Corrosion Behavior of Nanolayered TiN/NbN Multilayer Coatings Prepared by Reactive Direct Current Magnetron Sputtering Process[J]. Thin Solid Films, 2004, 460(1/2): 133-142.
[10] SUN W Q, LV Y J, GAO J P, et al.Enhanced Corrosion Resistance and Electrical Conductivity of Nb/NbN Multilayer Coatings Prepared by the Combination Methods of Magnetron Sputtering and Pulse Laser Deposition[J]. International Journal of Hydrogen Energy, 2025, 127: 160-168.
[11] GUDMUNDSSON J T, BRENNING N, LUNDIN D, et al.High Power Impulse Magnetron Sputtering Discharge[J]. Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films, 2012, 30(3): 030801.
[12] PURANDARE Y P, EHIASARIAN A P, HOVSEPIAN P E.Deposition of Nanoscale Multilayer CrN/NbN Physical Vapor Deposition Coatings by High Power Impulse Magnetron Sputtering[J]. Journal of Vacuum Science & Technology A: Vacuum, Surfaces, and Films, 2008, 26(2): 288-296.
[13] VILOAN R P B, GU J B, BOYD R, et al. Bipolar High Power Impulse Magnetron Sputtering for Energetic Ion Bombardment during TiN Thin Film Growth without the Use of a Substrate Bias[J]. Thin Solid Films, 2019, 688: 137350.
[14] LLOYD G E.Atomic Number and Crystallographic Contrast Images with the SEM: A Review of Backscattered Electron Techniques[J]. Mineralogical Magazine, 1987, 51(359): 3-19.
[15] SIKORA M, WOJCIESZAK D, CHUDZYŃSKA A, et al. Improved Methodology of Cross-Sectional SEM Analysis of Thin-Film Multilayers Prepared by Magnetron Sputtering[J]. Coatings, 2023, 13(2): 316.
[16] GÜTTLER D, ABENDROTH B, GRÖTZSCHEL R, et al. Mechanisms of Target Poisoning during Magnetron Sputtering as Investigated by Real-Time In-Situ Analysis and Collisional Computer Simulation[J]. Applied Physics Letters, 2004, 85(25): 6134-6136.
[17] DING J C, ZHANG T F, MEI H J, et al.Effects of Negative Bias Voltage and Ratio of Nitrogen and Argon on the Structure and Properties of NbN Coatings Deposited by HiPIMS Deposition System[J]. Coatings, 2018, 8(1): 10.
[18] PAULITSCH J, MAYRHOFER P H, MÜNZ W D, et al. Structure and Mechanical Properties of CrN/TiN Multilayer Coatings Prepared by a Combined HIPIMS/UBMS Deposition Technique[J]. Thin Solid Films, 2008, 517(3): 1239-1244.
[19] KOLCHEV S, KOLAKLIEVA L, CHITANOV V, et al.The Role of Period Modulation on the Structure, Composition and Mechanical Properties of Nanocomposite Multilayer TiAlSiN/AlSiN Coatings[J]. Coatings, 2023, 13(9): 1546.
[20] MITSCHKER F, PRENZEL M, BENEDIKT J, et al.Time-Resolved Measurement of Film Growth during Reactive High Power Pulsed Magnetron Sputtering (HIPIMS) of Titanium Nitride[J]. Journal of Physics D: Applied Physics, 2013, 46(49): 495201.
[21] LUBENCHENKO A V, BATRAKOV A A, SHURKAEVA I V, et al.XPS Study of Niobium and Niobium-Nitride Nanofilms[J]. Journal of Surface Investigation: X-ray, Synchrotron and Neutron Techniques, 2018, 12(4): 692-700.
[22] 王偕文, 吴思诚. 氮化铌表面氧化物的XPS研究[J]. 物理学报, 1985, 34(1): 112-116.
WANG X W, WU S C.XPS Study of the Oxides on the Surface of NbN Thin Film[J]. Acta Physica Sinica, 1985, 34(1): 112-116.
[23] POLLAK R A, STOLZ H J, RAIDER S I, et al.Chemical Composition and Interface Chemistry of Very Thin Nb2O5 Films Prepared by RF Plasma Oxidation[J]. Oxidation of Metals, 1983, 20(5): 185-192.
[24] IDRISS H.On the Wrong Assignment of the XPS O 1s Signal at 531-532 eV Attributed to Oxygen Vacancies in Photo- and Electro-Catalysts for Water Splitting and Other Materials Applications[J]. Surface Science, 2021, 712: 121894.
[25] ALOV N V, KUTSKO D M.Ion-Beam Reduction of the Surface of Higher Niobium Oxide[J]. Journal of Surface Investigation X-Ray, Synchrotron and Neutron Techniques, 2010, 4(2): 232-235.
[26] 潘晓龙, 胡小刚, 赵婧, 等. 薄膜/涂层材料界面结合强度评价方法研究进展[J]. 表面技术, 2022, 51(4): 50-65.
PAN X L, HU X G, ZHAO J, et al.Research Progress on Evaluation Methods of Interfacial Bonding Strength of Film/Coating[J]. Surface Technology, 2022, 51(4): 50-65.
[27] BAUYRZHAN R, ALEXANDER P, ZHULDYZ S, et al.Effect of Bilayer Thickness and Bias Potential on the Structure and Properties of (TiZr/Nb)N Multilayer Coatings as a Result of Arc-PVD Deposition[J]. Materials, 2022, 15(21): 7696.
[28] BOROWSKI T, FRYDRYCH J, SPYCHALSKI M, et al.Assessment of the Thermal Oxidation Effects on the Mechanical Properties of Magnetron-Sputtered NbN Coating Produced on AISI 316L Steel[J]. Coatings, 2026, 16(1): 106.
[29] MAO C H, SHUAI X F, WANG H B, et al.High Potential Corrosion Resistance and Conductivity Performance of C-Doped TiO2 Coatings Used in Bipolar Plates[J]. International Journal of Hydrogen Energy, 2025, 106: 366-376.
[30] XU J, PENG S, LI Z Y, et al.The Influence of Semiconducting Properties of Passive Films on the Cavitation Erosion Resistance of a NbN Nanoceramic Coating[J]. Ultrasonics Sonochemistry, 2021, 71: 105406.
[31] HU Q, LIU J M, SABOLA S A, et al.Alternating C- and Ti-Dominated Sublayers on Bipolar Plates Achieve Enhanced Corrosion Resistance under High Potentials Toward Proton Exchange Membrane Fuel Cells[J]. Corrosion Science, 2024, 234: 112125.
[32] VAN WESTING E P M, FERRARI G M, DE WIT J H W. The Determination of Coating Performance Using Electrochemical Impedance Spectroscopy[J]. Electrochimica Acta, 1994, 39(7): 899-910.
[33] ZHAO X J, HE L, XU Y, et al.HiPIMS-Deposited Nb/NbC/C Multilayer Coatings on 316L Stainless Steel for PEMFC Bipolar Plates[J]. Coatings, 2026, 16(6): 707.
[34] KESKAR K S, YAMASHITA T, ONODERA Y.Electrical Resistivity of Polycrystalline Niobium Nitride Films[J]. Japanese Journal of Applied Physics, 1987, 26: 1378-1380.
[35] CHAND M, MISHRA A, XIONG Y M, et al.Temperature Dependence of Resistivity and Hall Coefficient in Strongly Disordered NbN Thin Films[J]. Physical Review B, 2009, 80(13): 134514.