目的 对比考察MAX相Ti3AlC2及其衍生MXene Ti3AlC2Tₓ两种碳化物填料对火焰喷涂PEEK复合材料涂层微观结构、热稳定性、结晶行为及耐磨性能的影响规律。方法 以聚醚醚酮(PEEK)为基体,分别选用Ti3AlC2(MAX相)及其衍生的Ti3C2Tₓ(MXene)层状碳化物填料,采用火焰喷涂技术在17-4PH不锈钢表面制备PEEK基复合材料涂层,分别加入0.5%、1.0%、2.0%、5.0%(质量分数)Ti3AlC2或Ti3C2Tₓ,并通过SEM/EDS、FTIR、XRD、DSC、纳米压痕及摩擦磨损试验进行表征。结果 Ti3AlC2主要以块状或层状颗粒形式分布于PEEK基体中,低含量时可发挥填充作用并提高涂层致密性,高含量时则出现颗粒富集和孔隙增加;Ti3C2Tₓ主要以二维片层形式分布,含量过高时易发生片层堆叠,使涂层粗糙度和孔隙率升高。0.5% Ti3AlC2和Ti3C2Tₓ均可使1 708 cm-1处热降解C==O特征峰及2 919、2 851 cm-1处—CH2—伸缩振动峰强度有所降低,一定程度减弱PEEK热降解特征;当填料含量升至5.0%时,团聚加剧导致2 919、2 851 cm-1处特征峰强度上升,表明局部热量集中并促进分子链断裂。两种填料均未改变PEEK的基本晶体结构,其中Ti3AlC2的异相形核作用更明显,5.0%涂层结晶度达48.14%。Ti3AlC2与Ti3C2Tₓ对涂层硬度提升有限。Ti3AlC2有利于提高Ti3AlC2/PEEK复合材料涂层的耐磨性,2.0% Ti3AlC2/PEEK复合材料涂层比磨损率最低,为1.96×10-6 mm³/(N·m);Ti3C2Tₓ/PEEK复合材料涂层摩擦因数较低,但比磨损率整体高于PEEK涂层。结论 Ti3AlC2/PEEK复合材料涂层主要通过Ti3AlC2的颗粒支撑和承载作用改善耐磨性能,但Ti3C2Tₓ/PEEK复合材料中片层团聚及界面结合不足,摩擦过程中易发生片层剥落并形成硬质磨屑,引发磨粒磨损,加剧摩擦表面损伤。
Abstract
To clarify the different roles of a MAX-phase precursor and its derived MXene in flame-sprayed polyether ether ketone (PEEK) coatings, Ti3AlC2 and Ti3C2Tx were separately incorporated into PEEK at 0.5wt.%, 1.0wt.%, 2.0wt.%, and 5.0wt.%. Composite powders were deposited on 17-4PH stainless-steel substrates by flame spraying. The coating morphology, elemental distribution, chemical structure, crystallization behavior, thermal response, nanomechanical properties, and dry-sliding tribological properties were evaluated by SEM/EDS, FTIR, XRD, DSC, nanoindentation, and ball-on-disk testing. The two fillers produced distinctly different pore structures and interfacial configurations. At low contents, blocky or layered Ti3AlC2 particles filled interlamellar voids generated during spraying, so the porosity of the 0.5wt.% and 1.0wt.% Ti3AlC2/PEEK coatings was lower than that of neat PEEK. As the Ti3AlC2 content increased, particle enrichment, incomplete polymer encapsulation, and microgaps at the filler/matrix interfaces hindered the spreading and coalescence of molten PEEK, causing porosity to rise. Ti3C2Tx sheets contacted the matrix relatively closely in local regions; nevertheless, their high specific surface area and tendency to restack increased melt-flow resistance and retained voids between overlapping sheets. Consequently, the porosity of Ti3C2Tx/PEEK increased continuously with the filler content. FTIR results indicated that small filler additions partly suppressed the thermal-degradation features of PEEK, whereas agglomeration at high contents promoted local heat accumulation. XRD and DSC results showed that neither filler changed the basic crystalline structure of PEEK. Ti3AlC2 provided the stronger heterogeneous-nucleation effect: the crystallinity of the 5.0wt.% Ti2AlC2/PEEK coating reached 48.14%, and the 1.0wt.% coating exhibited the highest crystallization temperature, 293.3 ℃. Ti3C2Tx promoted crystallization at low contents, but sheet restacking and surface terminations increasingly restricted PEEK-chain mobility at higher contents. The nanohardness values of both composite series remained within a narrow range and were slightly lower than that of neat PEEK, while a decrease followed by a partial recovery was observed as the filler content increased. This non-monotonic response did not correspond directly to the cross-sectional average porosity because nanoindentation probes a small local volume. At low and intermediate contents, weak interfacial load transfer, interfacial sliding, and disruption of chain packing dominated, reducing the ability of the rigid filler to carry the indentation load. At high contents, locally filler-rich regions, contacts between rigid particles or overlapping sheets, and the increased crystallinity of Ti3AlC2/PEEK provided additional local support, producing a recovery in hardness or elastic modulus despite the higher average porosity. During sliding, Ti3AlC2 promoted a comparatively continuous and adherent transfer film. After running-in, this film separated the Si3N4 counterbody from the coating, suppressed repeated adhesion and detachment, and therefore produced smaller and more stable friction-coefficient fluctuations. In contrast, Ti3C2Tx- containing debris formed a temporary lubricating film that was less continuous and less strongly retained because of sheet agglomeration, interfacial defects, and loose wear debris. Repeated film formation, rupture, removal, and reformation alternated the contact between film-lubricated and direct or abrasive states, leading to pronounced friction fluctuations. At 5.0wt.% Ti3C2Tx, the greater supply of sheets improved film replenishment and reduced the mean friction coefficient, but the specific wear rate remained higher than that of neat PEEK. Ti3AlC2 was more effective in improving wear resistance: the 2.0wt.% Ti3AlC2/PEEK coating achieved the lowest specific wear rate of 1.96×10-6 mm3/(N·m), corresponding to 60.2% of the value for neat PEEK. These results demonstrated that Ti3AlC2 improved wear resistance mainly through particle supporting and load-bearing effects, whereas Ti3C2Tx aggravated damage to the friction surface due to abrasive wear induced by the formation of hard particulate wear debris.
关键词
PEEK /
火焰喷涂 /
Ti3C2Tx /
Ti3AlC2 /
复合涂层 /
摩擦磨损
Key words
PEEK /
flame spraying /
Ti3C2Tx /
Ti3AlC2 /
composite coating /
friction and wear
{{custom_sec.title}}
{{custom_sec.title}}
{{custom_sec.content}}
参考文献
[1] ZHAI L M, LUO Y Y, WANG Z W, et al.A Review on the Large Tilting Pad Thrust Bearings in the Hydropower Units[J]. Renewable and Sustainable Energy Reviews, 2017, 69: 1182-1198.
[2] 王伟光, 蔡龙, 李伟, 等. 复合材料推力瓦在油润滑轴承中应用的研究进展[J]. 大电机技术, 2019(2): 39-45.
WANG W G, CAI L, LI W, et al.Research Progress of Composite Thrust Pads in Oil-Lubricated Bearings[J]. Large Electric Machine and Hydraulic Turbine, 2019(2): 39-45.
[3] 杨子毅, 汤正阳, 薛炳, 等. 大型水轮机组推力轴承材料与结构及其润滑性能研究进展[J]. 表面技术, 2025, 54(20): 28-43.
YANG Z Y, TANG Z Y, XUE B, et al.Research Progress on Materials, Structures, and Lubrication Performance of Thrust Bearings in Large Hydro-Turbine Units[J]. Surface Technology, 2025, 54(20): 28-43.
[4] CHEN Y F, NI H J, PARK J J, et al.A Review of the Preparation, Modification, and Applications of Polyetheretherketone Coating[J]. Coatings, 2024, 14(11): 1451.
[5] CHEN B B, WANG J Z, YAN F Y.Comparative Investigation on the Tribological Behaviors of CF/PEEK Composites under Sea Water Lubrication[J]. Tribology International, 2012, 52: 170-177.
[6] PANIN S V, NGUYEN D A, BUSLOVICH D G, et al.Effect of Various Type of Nanoparticles on Mechanical and Tribological Properties of Wear-Resistant PEEK + PTFE-Based Composites[J]. Materials, 2021, 14(5): 1113.
[7] LI Y J, CHEN Y, GUO Y X, et al.Tribological Behavior of PEEK/PTFE Composites Reinforced with Carbon Fibers and Graphite[J]. Materials, 2022, 15(20): 7078.
[8] QIU X T, FU C L, GU A Q, et al.Preparation of High- Performance PEEK Anti-Wear Blends with Melt-Processable PTFE[J]. High Performance Polymers, 2020, 32(6): 645-654.
[9] QU S R, LO K H, WANG S S.Effect of Transfer Films on Friction of PTFE/PEEK Composite[J]. Journal of Tribology, 2021, 143(4): 041401.
[10] BARSOUM M W.The Mn+1AXn Phases: A New Class of Solids Thermodynamically Stable Nanolaminates[J]. Progress in Solid State Chemistry, 2000, 28(1/2/3/4): 201-281.
[11] EKLUND P, BECKERS M, JANSSON U, et al.The Mn+1AXn Phases: Materials Science and Thin-Film Processing[J]. Thin Solid Films, 2010, 518(8): 1851-1878.
[12] MAGNUSON M, NÄSLUND L Å. Local Chemical Bonding and Structural Properties in Ti3AlC2MAX Phase and Ti3C2TxMXene Probed by Ti 1s X-Ray Absorption Spectroscopy[J]. Physical Review Research, 2020, 2(3): 033516.
[13] JAVAID S, DEY M, KAABOUCH N, et al.On the Potential of Polyetheretherketone Matrix Composites Reinforced with Ternary Nanolaminates for Tribological and Biomedical Applications[J]. Journal of Applied Polymer Science, 2021, 138(10): 49980.
[14] NAGUIB M, KURTOGLU M, PRESSER V, et al.Two- Dimensional Nanocrystals Produced by Exfoliation of Ti3AlC2[J]. Advanced Materials, 2011, 23(37): 4248-4253.
[15] ANASORI B, LUKATSKAYA M R, GOGOTSI Y.2D Metal Carbides and Nitrides (MXenes) for Energy Storage[J]. Nature Reviews Materials, 2017, 2(2): 16098.
[16] SERLES P, HAMIDINEJAD M, DEMINGOS P G, et al.Friction of Ti3C2Tx MXenes[J]. Nano Letters, 2022, 22(8): 3356-3363.
[17] GRÜTZMACHER P G, SUAREZ S, TOLOSA A, et al. Superior Wear-Resistance of Ti3C2TxMultilayer Coatings[J]. ACS Nano, 2021, 15(5): 8216-8224.
[18] XUE L L, XU Q Q, MENG C H, et al.Achieving the Ultra-Low Friction and Wear Rate of PEEK-PTFE Composites by Ti3C2Tx MXene Reinforcement[J]. Tribology International, 2024, 199: 110030.
[19] KOIVULUOTO H.A Review of Thermally Sprayed Polymer Coatings[J]. Journal of Thermal Spray Technology, 2022, 31(6): 1750-1764.
[20] THARAJAK J, PALATHAI T, SOMBATSOMPOP N.Morphological and Physical Properties and Friction/Wear Behavior of h-BN Filled PEEK Composite Coatings[J]. Surface and Coatings Technology, 2015, 273: 20-29.
[21] 李昱鹏, 解佳琦, 张硕累, 等. 火焰喷涂石墨改性CF/PEEK复合材料涂层及其摩擦学性能[J]. 中国表面工程, 2025, 38(5): 215-225.
LI Y P, XIE J Q, ZHANG S L, et al.Flame Spraying Graphite Modified CF/PEEK Composite Coating and Its Tribological Properties[J]. China Surface Engineering, 2025, 38(5): 215-225.
[22] 武中德, 张宏. 水轮发电机组推力轴承技术的发展[J]. 电器工业, 2007(1): 32-36.
WU Z D, ZHANG H.Development of Thrust Bearing Technology for Hydro-Generator Units[J]. China Electrical Equipment Industry, 2007(1): 32-36.
[23] PATTERSON A L.The Scherrer Formula for X-Ray Particle Size Determination[J]. Physical Review, 1939, 56(10): 978-982.
[24] OLIVER W C, PHARR G M.An Improved Technique for Determining Hardness and Elastic Modulus Using Load and Displacement Sensing Indentation Experiments[J]. Journal of Materials Research, 1992, 7(6): 1564-1583.
[25] 魏胜敏, 李英, 常明, 等. 聚醚醚酮的红外光谱研究[J]. 合成树脂及塑料, 2019, 36(2): 27-31.
WEI S M, LI Y, CHANG M, et al.Research on Infrared Spectroscopy of PEEK[J]. China Synthetic Resin and Plastics, 2019, 36(2): 27-31.
[26] FUENTE E, MENÉNDEZ J A, DÍEZ M A, et al. Infrared Spectroscopy of Carbon Materials: A Quantum Chemical Study of Model Compounds[J]. The Journal of Physical Chemistry B, 2003, 107(26): 6350-6359.
[27] GAITANELIS D, WORRALL C, KAZILAS M.Detecting, Characterising and Assessing PEEK’s and CF-PEEK’s Thermal Degradation in Rapid High-Temperature Processing[J]. Polymer Degradation and Stability, 2022, 204: 110096.
[28] JANG J, LEE Y, CHEONG H, et al.Defects and Mechanical Properties of Silicon Nitride Ball Bearings for Electric Vehicle Reducers[J]. World Electric Vehicle Journal, 2024, 15(6): 272.
[29] YAO L, ZHU C C, JIANG J X, et al.Mechanical Properties of Ti3AlC2 Ceramics before and after Heat Treatment[J]. Rare Metals, 2022, 41(8): 2777-2782.
[30] ZAMBRANO D, WANG B, DUAN B C, et al.Interplay between Mechanical Properties and Tribological Performance for Multilayer Ti3C2Tx Coatings[J]. Surfaces and Interfaces, 2025, 72: 107375.
[31] LI Y P, MAN Z Q, LIN X Y, et al.Role of Well-Dispersed Carbon Nanotubes and Limited Matrix Degradation on Tribological Properties of Flame-Sprayed PEEK Nanocomposite Coatings[J]. Journal of Tribology, 2022, 144: 012101.
基金
国家重点研发计划资助项目(2024YFB3410801); 辽宁省科技计划项目(2023JH1/10400052)