石文天,王林,李杰,闫天明,刘玉德.基于MQL的碳纤维复合材料制孔表面质量及切削力试验[J].表面技术,2023,52(5):235-246.
SHI Wen-tian,WANG Lin,LI Jie,YAN Tian-ming,LIU Yu-de.Experiment on Hole Making Surface Quality and Cutting Force of Carbon Fiber Reinforced Composite Based on MQL[J].Surface Technology,2023,52(5):235-246 |
| 基于MQL的碳纤维复合材料制孔表面质量及切削力试验 |
| Experiment on Hole Making Surface Quality and Cutting Force of Carbon Fiber Reinforced Composite Based on MQL |
| |
| DOI：10.16490/j.cnki.issn.1001-3660.2023.05.023 |
| 中文关键词: 碳纤维增强复合材料 微量润滑 切削力 制孔尺寸精度 进给速度 |
| 英文关键词:carbon fiber reinforced polymer minimum quantity lubrication cutting force hole making dimensional accuracy feed speed |
| 基金项目:国家自然科学基金(51975006，51505006) |
| 作者 | 单位 |
| 石文天 | 北京工商大学 人工智能学院，北京 100048 |
| 王林 | 北京工商大学 人工智能学院，北京 100048 |
| 李杰 | 北京工商大学 人工智能学院，北京 100048 |
| 闫天明 | 北京工商大学 人工智能学院，北京 100048 |
| 刘玉德 | 北京工商大学 人工智能学院，北京 100048 |
|
| Author | Institution |
| SHI Wen-tian | School of Artificial Intelligence, Beijing Technology and Business University, Beijing 100048, China |
| WANG Lin | School of Artificial Intelligence, Beijing Technology and Business University, Beijing 100048, China |
| LI Jie | School of Artificial Intelligence, Beijing Technology and Business University, Beijing 100048, China |
| YAN Tian-ming | School of Artificial Intelligence, Beijing Technology and Business University, Beijing 100048, China |
| LIU Yu-de | School of Artificial Intelligence, Beijing Technology and Business University, Beijing 100048, China |
|
| 摘要点击次数: |
| 全文下载次数: |
| 中文摘要: |
| 目的 减少碳纤维增强复合材料(CFRP)制孔表面毛刺及边缘凸起等缺陷。方法 对比研究在干切削和微量润滑(MQL)2种加工条件下碳纤维增强复合材料(CFRP)的制孔，在切削速度一定时，探究切削方式、进给速度对制孔尺寸精度、表面质量、切削力的影响。采用方差分析对各影响因素及其权重进行分析。结果 得出了切削方式和工艺参数对制孔尺寸精度、切削力、表面质量的影响规律。试验结果表明，在微量润滑条件下，由于润滑和降温的影响，表面毛刺得到有效去除，纤维断面平整，剪切作用明显，抑制了由温升所引起的边缘隆起膨胀现象，试样的表面质量得到显著提高，切削力整体降低。在干切削和微量润滑条件下对制孔尺寸精度影响最大的是切削方式。对于切削力，在干切削时受到切削方式的影响最大，在微量润滑条件下受到进给速度的影响最大，随着进给速度的增大而增大。结论 在现有试验条件下，微量润滑的加工质量总体上优于干切削的加工质量，其制孔尺寸的精度整体更高，其切削力最大降低了84.26%。 |
| 英文摘要: |
| The work aims to reduce the defects such as burrs and raised edges on the hole making surface of carbon fiber reinforced polymer (CFRP). A comparative study was conducted to investigate the effect of cutting method and feed speed on the dimensional accuracy, surface quality and cutting force of CFRP under both dry cutting and minimum quantity lubrication (MQL) machining conditions. Analysis of variance (ANOVA) was used to analyze each affecting factor and its factor weights. The effect of cutting method and process parameters on the dimensional accuracy, cutting force and surface quality of the hole was revealed. The experimental results indicated that under the minimum quantity lubrication condition, the surface burr was effectively suppressed due to the effect of lubrication and temperature reduction, the fiber section was flat, the shearing effect was obvious, the edge bulge expansion caused by temperature rise was suppressed, the maximum reduction of hole making dimensional deviation was 9.70%, and the minimum value was 1.162. Therefore, the hole making dimensional accuracy and surface quality were improved. Under the cutting force of drilling hole making and milling hole making methods, the cutting force was reduced overall, and the minimum value of cutting force was 3.36 N, and the cutting force fluctuation became smaller and more stable which was weakened by the impact and the tool wear resistance was enhanced. The great affecting factor on hole making dimensional accuracy under dry cutting and minimum quantity lubrication conditions was the cutting method. For cutting force, it was mostly affected by the cutting method under dry cutting and by the feed speed under minimum quantity lubrication conditions, and it increased with the increase of feed speed. According to the experimental results, the overall quality of minimum quantity lubrication processing under the existing conditions is better than that under dry cutting. Compared with that under dry cutting, the overall hole making dimensional accuracy is improved by 6.55%, the maximum cutting force is reduced by 84.26%, and the milling hole making is better than drilling. |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| 关闭 |
|
|
|
渝公网安备 50010702501715号