黄粉超,焦剑,程皓,王瑾,王佳.TiO2对中空硅减反射涂层硬度的影响[J].表面技术,2021,50(4):191-197.
HUANG Fen-chao,JIAO Jian,CHENG Hao,WANG Jin,WANG Jia.Effect of TiO2 on the Hardness of Hollow Silica Antireflection Coating[J].Surface Technology,2021,50(4):191-197 |
| TiO2对中空硅减反射涂层硬度的影响 |
| Effect of TiO2 on the Hardness of Hollow Silica Antireflection Coating |
| 投稿时间：2020-03-23 修订日期：2020-05-26 |
| DOI：10.16490/j.cnki.issn.1001-3660.2021.04.018 |
| 中文关键词: 减反射涂层 溶胶-凝胶 中空SiO2 纳米TiO2 硬度 透射率 |
| 英文关键词:AR coatings sol-gel hollow SiO2 nano-TiO2 hardness transmittance |
| 基金项目: |
| 作者 | 单位 |
| 黄粉超 | 西安超码科技有限公司，西安 710025 |
| 焦剑 | 西北工业大学，西安 710129 |
| 程皓 | 西安超码科技有限公司，西安 710025 |
| 王瑾 | 西北工业大学，西安 710129 |
| 王佳 | 西北工业大学，西安 710129 |
|
| Author | Institution |
| HUANG Fen-chao | Xi’an ChaoMa Technology Co., Ltd, Xi’an 710025, China |
| JIAO Jian | Northwestern Polytechnical University, Xi’an 710129, China |
| CHENG Hao | Xi’an ChaoMa Technology Co., Ltd, Xi’an 710025, China |
| WANG Jin | Northwestern Polytechnical University, Xi’an 710129, China |
| WANG Jia | Northwestern Polytechnical University, Xi’an 710129, China |
|
| 摘要点击次数: |
| 全文下载次数: |
| 中文摘要: |
| 目的 提高中空硅减反射(AR)涂层的硬度。方法 采用溶胶-凝胶法制备中空二氧化硅纳米微球(HSNs)胶体溶液，通过异丙醇钛(TTIP)的水解缩合作用，在HSNs表面沉积纳米TiO2后，制备HSNs@TiO2胶体溶液。将HSNs@TiO2胶体溶液与酸性硅溶胶(ACSS)复合，制备HSNs@TiO2/ACSS减反射液，通过旋涂法在玻璃基板上制备相应的AR涂层。通过特高分辨率场发射扫描电子显微镜、高分辨透射电子显微镜和原子力显微镜对HSNs和HSNs@TiO2纳米粒子的形貌进行分析，通过紫外-可见分光光度计和纳米压痕仪对HSNs/ACSS AR涂层和HSNs@TiO2/ACSS AR涂层的透射率、硬度和弹性模量分别进行分析。结果 纳米TiO2沉积在HSNs表面后，减反射液中HSNs@TiO2纳米粒子的粒径较HSNs粒径增大1~30 nm不等。由HSNs@TiO2/ACSS减反射液制备的AR涂层表面颗粒及团簇明显，表面粗糙度(RMS)可达9.61 nm，远高于HSNs/ACSS AR涂层的3.62 nm。含有较大粒径HSNs@TiO2纳米粒子的HSNs@TiO2/ACSS AR涂层使玻璃基板在550 nm波长处的透射率增加1.3%，低于HSNs/ACSS AR涂层的增加值2.8%。纳米TiO2沉积之前，HSNS/ACSS AR涂层的硬度和弹性模量分别为2.3 GPa和56.3 GPa，纳米TiO2沉积之后，HSNs@TiO2/ACSS AR涂层的硬度和弹性模量分别为3.3 GPa和55.2 GPa，AR涂层的硬度显著提高。结论 溶胶-凝胶法在HSNs上沉积纳米TiO2后，可有效提高AR涂层的硬度，因此AR涂层的环境适用性有望得到进一步提高。 |
| 英文摘要: |
| The purpose is to improve the hardness of hollow silica antireflection (AR) coatings. In this paper, a colloidal solution of hollow silica nanospheres (HSNs) is prepared by sol-gel method, and HNSs@TiO2 colloidal solution is prepared by depositing nano-TiO2 on the surface of HSNs through hydrolysis and condensation of titanium isopropoxide (TTIP). The HSNs@TiO2/ACSS AR solution is prepared by mixed the HSNs@TiO2 colloidal solution and acidic silica sol (ACSS). The morphology of HSNs and HSNs@TiO2 nanoparticles are analyzed by ultra-high resolution field emission scanning electron microscope, high-resolution transmission electron microscope and atomic force microscope. The transmittance, hardness and elastic modulus of HSNs/ACSS AR coating and HSNs@TiO2/ACSS AR coating are analyzed by UV-visible spectrophotometer and nanoindenter respectively. After the nano-TiO2 is deposited on the surface of HSNs, the particle size of the HSNs@TiO2 nanoparticles in antireflection liquid increased by 1~30 nm compared with the particle size of the HSNs; Particles and clusters on the surface of AR coating that prepared by HSNs@TiO2/ACSS AR liquid are obvious, and the surface roughness (RMS) of the AR coating could reach 9.61 nm, which is much higher than 3.62 nm of HSNs/ACSS AR coating; HSNs@TiO2/ACSS AR coating with larger HSNs@TiO2 nanoparticles increased the transmittance of glass at 550 nm by 1.3%, which is lower than 2.8% of HSNs/ACSS AR coating; Before the nano-TiO2 deposited, the hardness and elastic modulus of the HSNS/ACSS AR coating are 2.3 GPa and 56.3 GPa, respectively, the hardness of the AR coating is significantly improved after the nano-TiO2 deposited, the hardness and elastic modulus of the HSNs@TiO2/ACSS AR coating are 3.3 GPa and 55.2 GPa, respectively. The nano-TiO2 deposited on HSNs by sol-gel method could effectively improve the hardness of AR coatings, so the environmental applicability of AR coatings is expected to be further improved. |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| 关闭 |
|
|
|
渝公网安备 50010702501715号