王怡静,郝恩康,赵晓琴,安宇龙,周惠娣.NiCrWMoCuCBFe涂层的制备及其力学性能研究[J].表面技术,2019,48(9):185-192.
WANG Yi-jing,HAO En-kang,ZHAO Xiao-qin,AN Yu-long,ZHOU Hui-di.Preparation and Mechanical Properties of NiCrWMoCuCBFe Coatings[J].Surface Technology,2019,48(9):185-192 |
| NiCrWMoCuCBFe涂层的制备及其力学性能研究 |
| Preparation and Mechanical Properties of NiCrWMoCuCBFe Coatings |
| 投稿时间：2019-04-25 修订日期：2019-09-20 |
| DOI：10.16490/j.cnki.issn.1001-3660.2019.09.020 |
| 中文关键词: NiCrWMoCuCBFe涂层 超音速火焰喷涂 微观结构 力学性能 结合强度 三点弯曲试验 |
| 英文关键词:NiCrWMoCuCBFe coating HVOF microstructure mechanical properties bonding strength three-point bending test |
| 基金项目:国家自然科学基金（51771214）；中国科学院青年促进会（2014378）；中国科学院“西部之光”；甘肃省科技计划项目（17JR5RA300） |
| 作者 | 单位 |
| 王怡静 | 1.中国科学院兰州化学物理研究所 固体润滑国家重点试验室，兰州 730000；2.中国科学院大学 材料与光电研究中心，北京 100049 |
| 郝恩康 | 1.中国科学院兰州化学物理研究所 固体润滑国家重点试验室，兰州 730000；2.中国科学院大学 材料与光电研究中心，北京 100049 |
| 赵晓琴 | 1.中国科学院兰州化学物理研究所 固体润滑国家重点试验室，兰州 730000 |
| 安宇龙 | 1.中国科学院兰州化学物理研究所 固体润滑国家重点试验室，兰州 730000；2.中国科学院大学 材料与光电研究中心，北京 100049 |
| 周惠娣 | 1.中国科学院兰州化学物理研究所 固体润滑国家重点试验室，兰州 730000；2.中国科学院大学 材料与光电研究中心，北京 100049 |
|
| Author | Institution |
| WANG Yi-jing | 1.State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, China; 2.Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China |
| HAO En-kang | 1.State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, China; 2.Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China |
| ZHAO Xiao-qin | 1.State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, China |
| AN Yu-long | 1.State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, China; 2.Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China |
| ZHOU Hui-di | 1.State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000, China; 2.Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China |
|
| 摘要点击次数: |
| 全文下载次数: |
| 中文摘要: |
| 目的 探究NiCrWMoCuCBFe涂层的微观组织结构、物相组成及其力学性能。方法 通过霍尔流速计表征了喷涂粉末的流动性和松装密度，采用超音速火焰喷涂在316L不锈钢表面制备了NiCrWMoCuCBFe涂层，利用SEM、EDS分别对喷涂粉末的形貌、涂层的组织结构以及粉末和涂层中的元素组成进行了表征，采用XRD、Raman分析了涂层中的物相，使用显微硬度计及万能材料试验机考察涂层的硬度、结合强度和抗弯强度，并分析了涂层的断裂失效机理。结果 NiCrWMoCuCBFe喷涂粉末具有良好的流动性，在喷涂过程中没有发生严重的氧化现象。通过超音速火焰喷涂制备的NiCrWMoCuCBFe涂层具有致密的层状组织结构，其物相主要是Ni基固溶体，但是也出现了少量的NiO和Cr2O3。此外，涂层的截面硬度与表面硬度相当，约为600HV300 g，且涂层与316L不锈钢的结合强度较高，大于70 MPa。三点弯曲试验中，持续加载至载荷为1800 N，应变为(4.81±0.3)%时，涂层达到强度极限，产生明显的塑性变形；而当载荷仍然保持1800 N，应变继续增加达到(11.43±0.03)％时，涂层与316L不锈钢基材的结合界面彻底开裂失效，此时涂层内部同时具有横向裂纹和纵向裂纹，样品的抗弯强度约为(1.87±0.02) GPa。结论 超音速火焰技术制备出的NiCrWMoCuCBFe涂层具有良好的致密性及优异的力学性能。 |
| 英文摘要: |
| The work aims to study the microstructure, composition and mechanical properties of NiCrWMoCuCBFe coating. The flowability and bulk density (apparent density) of the sprayed powder was characterized by Hall flowmeter. Then, NiCrWMoCuCBFe coating was prepared on 316L stainless steel substrate by High Velocity Oxygen Fuel (HVOF) spraying technique. The morphologies, microstructure and element compositions of the powder and the coating were investigated by SEM and EDS. The phases of the coating were characterized by XRD and Raman. Besides, the hardness, bonding strength and flexural strength of the coating were investigated by microhardness tester and universal material testing machine and then the fracture failure mechanism of the coating was analyzed. The NiCrWMoCuCBFe sprayed powder had great fluidity and was hardly oxidized in the process of spraying. The HVOF-sprayed NiCrWMoCuCBFe coating was very dense and exhibited typical lamellar structure. The coating was mainly composed of Ni-based solid solution and a small amount of NiO and Cr2O3 on the surface. In addition, the hardness of the coating cross section was approximately equal to that of surface which was about 600HV300g. The bonding strength between the coating and 316L stainless steel was larger than 70 MPa. When the load increased to 1800 N in the three-point bending test, the coating reached the strength limit with the strain about (4.81±0.3)%. Meanwhile, there was obvious plastic deformation. When the load remained unchanged, but the strain rose up to (11.43±0.03)%, the bonding interface between coating and 316L stainless steel substrate broke and failed. Thus, there were obvious transverse and longitudinal cracks inside the coating and the bending strength of the sample was about (1.87±0.02) GPa. HVOF-prepared NiCrWMoCuCBFe coating has excellent compactness and mechanical properties. |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| 关闭 |
|
|
|
渝公网安备 50010702501715号