邹云,桑振宽,李大磊,李阳.304不锈钢水射流强化工艺的多目标优化设计[J].表面技术,2018,47(2):25-29.
ZOU Yun,SANG Zhen-kuan,LI Da-lei,LI Yang.Multi-objective Optimal Design of Enhancing Technology for 304 Stainless Steel by Water Jet Peening[J].Surface Technology,2018,47(2):25-29 |
| 304不锈钢水射流强化工艺的多目标优化设计 |
| Multi-objective Optimal Design of Enhancing Technology for 304 Stainless Steel by Water Jet Peening |
| 投稿时间：2017-07-24 修订日期：2018-02-20 |
| DOI：10.16490/j.cnki.issn.1001-3660.2018.02.005 |
| 中文关键词: 水射流 304不锈钢 正交试验 多目标优化设计 残余应力 粗糙度 |
| 英文关键词:water jet peening 304 stainless steel orthogonal test multi-objective optimal design residual stress roughness |
| 基金项目: |
|
|
| Author | Institution |
| ZOU Yun | 1.School of Mechanical Engineering, Zhengzhou University, Zhengzhou 450001, China; 2.Henan Province Engineering Laboratory for Anti-fatigue Manufacturing Technology, Zhengzhou 450001, China |
| SANG Zhen-kuan | 1.School of Mechanical Engineering, Zhengzhou University, Zhengzhou 450001, China; 2.Henan Province Engineering Laboratory for Anti-fatigue Manufacturing Technology, Zhengzhou 450001, China |
| LI Da-lei | 1.School of Mechanical Engineering, Zhengzhou University, Zhengzhou 450001, China; 2.Henan Province Engineering Laboratory for Anti-fatigue Manufacturing Technology, Zhengzhou 450001, China |
| LI Yang | 1.School of Mechanical Engineering, Zhengzhou University, Zhengzhou 450001, China; 2.Henan Province Engineering Laboratory for Anti-fatigue Manufacturing Technology, Zhengzhou 450001, China |
|
| 摘要点击次数: |
| 全文下载次数: |
| 中文摘要: |
| 目的 得到水射流强化技术工艺参数（水压、靶距、速度、进给量）对304不锈钢表层性能指标（残余应力、硬度和粗糙度）的影响程度。方法 采用X射线残余应力分析仪、三维形貌仪和显微硬度计，分别测试304不锈钢水射流后表面的残余应力、粗糙度和显微硬度值。利用显著性方法分析正交试验结果，并通过多目标优化设计对不同水射流工艺参数下的强化效果进行综合性研究。结果 影响304不锈钢表层性能指标的水射流工艺参数由强到弱的顺序依次为：进给量、水压、速度和靶距。经过多目标优化设计，得到了304不锈钢水射流强化工艺参数的最佳组合：水压300 MPa，靶距15 mm，速度400 mm/min，进给量0.125 mm。结论 水射流工艺参数的制定主要考虑进给量和水压两者的影响，而速度和靶距对表层性能指标的影响较小。 |
| 英文摘要: |
| The work aims to explore effects of process parameters (water pressure, target distance, speed and feed) of water jet peening enhancing technology on performance indicators (residual stress, hardness, roughness) of 304 stainless steel surface. The residual stress, roughness and microhardness of the surface receiving water jet peening were tested with XRD stress analyzer, optical profilometer and microhardness tester, respectively. Orthogonal test results were analyzed in significance approach, and enhancing effects provided with different water jet peening process parameters were comprehensively studied based upon multi-objective optimal design. It was found that feed rate had the greatest effect on the mechanical properties, then water pressure and speed, and finally target distance. Based upon the multi-objective optimal design, the best parameter combination for 304 stainless steel enhanced by water jet peening was obtained: water pressure as 300 MPa, target distance as 15 mm, speed as 400 mm/min and feed rate as 0.125 mm. Effects of feed rate and water pressure are mainly considered to determine water jet peening process parameters while those of speed and target distance can be neglected. |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| 关闭 |
|
|
|
渝公网安备 50010702501715号