附青山,金永中,余祖孝,李明田.pH 值对 TiCN 粉末表面镀 Co 的影响[J].表面技术,2014,43(5):91-94,117.
FU Qing-shan,JIN Yong-zhong,YU Zu-xiao,LI Ming-tian.Effect of pH on Co Plating on TiCN Surface[J].Surface Technology,2014,43(5):91-94,117 |
| pH 值对 TiCN 粉末表面镀 Co 的影响 |
| Effect of pH on Co Plating on TiCN Surface |
| 投稿时间：2014-05-14 修订日期：2014-07-07 |
| DOI： |
| 中文关键词: TiCN 粉末 化学镀 镀钴 pH 值 |
| 英文关键词:TiCN powder electroless plating Co plating pH |
| 基金项目:四川理工学院人才引进项目 ( 2012RC04,012RC08) ; 材料腐蚀与防护四川省重点实验室项目 ( 2013CL11 ) |
| 作者 | 单位 |
| 附青山 | 四川理工学院 材料与化学工程学院, 四川 自贡 643000;四川省腐蚀与防腐重点实验室, 四川 自贡 643000 |
| 金永中 | 四川理工学院 材料与化学工程学院, 四川 自贡 643000;四川省腐蚀与防腐重点实验室, 四川 自贡 643000 |
| 余祖孝 | 四川理工学院 材料与化学工程学院, 四川 自贡 643000;四川省腐蚀与防腐重点实验室, 四川 自贡 643000 |
| 李明田 | 四川理工学院 材料与化学工程学院, 四川 自贡 643000;四川省腐蚀与防腐重点实验室, 四川 自贡 643000 |
|
| Author | Institution |
| FU Qing-shan | College of Material and Chemical Engineering, Sichuan University of Science and Engineering, Zigong 643000, China;Material Corrosion and Protection Key Laboratory of Sichuan Province, Zigong 643000, China |
| JIN Yong-zhong | College of Material and Chemical Engineering, Sichuan University of Science and Engineering, Zigong 643000, China;Material Corrosion and Protection Key Laboratory of Sichuan Province, Zigong 643000, China |
| YU Zu-xiao | College of Material and Chemical Engineering, Sichuan University of Science and Engineering, Zigong 643000, China;Material Corrosion and Protection Key Laboratory of Sichuan Province, Zigong 643000, China |
| LI Ming-tian | College of Material and Chemical Engineering, Sichuan University of Science and Engineering, Zigong 643000, China;Material Corrosion and Protection Key Laboratory of Sichuan Province, Zigong 643000, China |
|
| 摘要点击次数: |
| 全文下载次数: |
| 中文摘要: |
| 目 的 研究 TiCN 粉末表面镀 Co 时, 镀液 pH 值对施镀过程的影响。 方法 采用 低温化学镀工艺在 TiCN 粉末表面镀 Co。 用 氨水调节镀液的初始 pH 值, 考查初始 pH 值对镀层形成速率的影响及 pH值在施镀过程中的变化情况。 分析施镀前后, TiCN 表面相和形貌的变化。 结果 在碱性范围 内 , 随着镀液初始 pH 值的增加, 镀速呈先增大、后减小的趋势。 镀液初始 pH 值为 9 时, 镀速最高, 且随着施镀的进行, 镀液 pH 值明显降低, 有大量气泡产生, 大约 0. 5 h 后, pH 值趋于稳定。 TiCN 表面镀覆了 较完整的 Co层。 结论 通过控制 镀液的初始 pH 值, 可以调整 TiCN 表面镀 Co 的效率。 在 85 ℃ 的 温度下, 镀液 pH为 9 时, 能得到较高的镀覆效率。 |
| 英文摘要: |
| Objective To study the effect of plating solution pH on the electroless plating process during the Co plating on the surface of TiCN powder. Methods Co was coated on the surface of TiCN powder by low-temperature electroless plating. The initial pH of the plating solution was adjusted by ammonium, and the effect of initial pH on the coating formation rate and the change of pH during the plating process were studied. Besides, the changes in phase composition and surface morphology of TiCN before and after plating were analyzed. Results Within the alkaline range, the plating rate first increased and then decreased with the increasing initial pH of the plating solution. The highest plating rate was observed when the initial pH of the plating solution was 9. During the plating process, the pH of the plating solution decreased obviously, with the production of a large amounts of bubbles. After 0. 5 h, the pH value became stable. A uniform Co coating formed on the surface of TiCN. Conclusion By adjustment the initial pH of the plating solution, the efficiency of Co plating on the surface of TiCN. High plating rate was observed at pH = 9 and 85 ℃ . |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| 关闭 |
|
|
|
渝公网安备 50010702501715号