许斌,刘春明,安成强,王双红,于晓中.冷轧板的各工序形貌及表面清洁度分析[J].表面技术,2010,39(4):53-54,112.
XU Bin,LIU Chun-ming,AN Cheng-qiang,WANG Shuang-hong,YU Xiao-zhong.Study on the Surface Morphology and Cleanness of Different Process on Cold-rolled Steel[J].Surface Technology,2010,39(4):53-54,112
冷轧板的各工序形貌及表面清洁度分析
Study on the Surface Morphology and Cleanness of Different Process on Cold-rolled Steel
投稿时间:2010-05-20  修订日期:2010-08-10
DOI:
中文关键词:  表面形貌  清洁度  残留物  冷轧板
英文关键词:surface morphology  cleanness  residuum  cold-rolled steel
基金项目:
作者单位
许斌 1.东北大学材料与冶金学院,沈阳110819; 2.河北钢铁集团邯钢公司,邯郸056015 
刘春明 东北大学材料与冶金学院,沈阳110819 
安成强 1.沈阳理工大学环境与化工学院,沈阳110168;2.东北大学金属防护技术工程研究中心,沈阳110819 
王双红 东北大学材料与冶金学院,沈阳110819 
于晓中 东北大学金属防护技术工程研究中心,沈阳110819 
AuthorInstitution
XU Bin 1.School of Materials and Metallurgy, Northeastern University, Shenyang 110819, China;2.Handan Iron& Steel Group Co Ltd, Hebei Iron& Steel Group Co Ltd, Handan 056015, China 
LIU Chun-ming School of Materials and Metallurgy, Northeastern University, Shenyang 110819, China 
AN Cheng-qiang 1.School of Environment& Chemical Engineering, Shenyang Ligong University, Shenyang 110159, China;2.Engineering Research Center of Metal Protection Technology, Northeastern University, Shenyang 110819, China 
WANG Shuang-hong School of Materials and Metallurgy, Northeastern University, Shenyang 110819, China 
YU Xiao-zhong Engineering Research Center of Metal Protection Technology, Northeastern University, Shenyang 110819, China 
摘要点击次数:
全文下载次数:
中文摘要:
      借助激光共聚焦显微镜、电化学方法、称量法和分光光度法分析了冷轧板在不同工序的微观形貌、耐蚀性及其残留物总量和残铁量。结果表明:不同工序的表面形貌相差不大且耐蚀性差别也不显著;不同工序的表面清洁度有明显差别,其中冷轧工序残留物总量最多;同一工序的板材的不同位置表面残留物含量也略有不同,中间部位的残留物含量小于操作侧和驱动侧。
英文摘要:
      Microcosmic morphology, corrosion resistance, total amount of surface residuum and the amount of iron residuum on cold-rolled steel were analyzed by means of laser scanning confocal microscope, electrochemical test, weighing method and spectrophotometer. The results show that the surface morphology and corrosion resistance are indistinctively different during different process; The difference of surface cleanness of different process is obvious, the most amount of surface residuum is cold rolling process; The surface cleanness is slightly different at different positions during same process, and the amount of residuum at middle position is less than other position.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第20720651位访问者    渝ICP备15012534号-3

版权所有:《表面技术》编辑部 2014 surface-techj.com, All Rights Reserved

邮编:400039 电话:023-68792193传真:023-68792396 Email: bmjs@surface-techj.com

渝公网安备 50010702501715号