姜伟,戚佳睿,孙海霞.30CrMnSi镀铬后激光表面合金化[J].表面技术,2008,37(4):29-30.
JIANG Wei,QI Jia-rui,SUN Hai-xia.Laser Surface Alloying on 30CrMnSi Electroplated with Cr[J].Surface Technology,2008,37(4):29-30 |
| 30CrMnSi镀铬后激光表面合金化 |
| Laser Surface Alloying on 30CrMnSi Electroplated with Cr |
| 投稿时间：2008-02-22 修订日期：2008-08-10 |
| DOI： |
| 中文关键词: 激光表面合金化 30CrMnSi 工艺参数 金相组织 显微硬度 镀铬 |
| 英文关键词:Laser surface alloying 30CrMnSi Parameters Microstructure Micro-hardness Chrome plating |
| 基金项目: |
| 作者 | 单位 |
| 姜伟 | 海军航空工程学院青岛分院，山东青岛266041 |
| 戚佳睿 | 海军航空工程学院青岛分院，山东青岛266041 |
| 孙海霞 | 海军航空工程学院青岛分院，山东青岛266041 |
|
| Author | Institution |
| JIANG Wei | Aviation Department of Mechanical Engineering, Qingdao Branch, Naval Aeronautical Engineering Academy, Qingda0 266041, China |
| QI Jia-rui | Aviation Department of Mechanical Engineering, Qingdao Branch, Naval Aeronautical Engineering Academy, Qingda0 266041, China |
| SUN Hai-xia | Aviation Department of Mechanical Engineering, Qingdao Branch, Naval Aeronautical Engineering Academy, Qingda0 266041, China |
|
| 摘要点击次数: |
| 全文下载次数: |
| 中文摘要: |
| 为研究激光表面合金化工艺对镀铬后30CrMnSi组织与硬度的影响，以C02激光器为热源，采用正交试验法，对其表面进行单道扫描，获得了金相组织和显微硬度均优于基体的合金化层。研究结果表明：激光合金化层晶粒显著细化，平均硬度明显高于基体硬度。激光功率500W，扫描速度10 mm/s，保护气体流量10L/min时，合金化层组织细小均匀致密，最高硬度达829HV，约是基体硬度的2.6倍。 |
| 英文摘要: |
| For studying the impact of microstructure and micro-hardness of 30CrMnSi electroplated with Cr by laser surface alloying, using C02 laser as heat source and orthogonal test, the alloying layers by single-channel scanning were attained whose microstructure and micro-hardness were better than the substrates: The results indicate that: the laser alloying layers microstructure is refined remarkably, and the average micro-hardness is higher than the substrates'obviously. When laser power is 500W, scanning speed is lOmm/s and the protection of gas flow is lOL/min, the alloying layer has small dense uniform and the highest micro-hardness of 829HV is about 2. 6 times in contrast of the substrate's. |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| 关闭 |
|
|
|
渝公网安备 50010702501715号