孙伟超,许竞,林星魁,艾力.伊沙木丁.光学望远镜镜片旋转镀膜修正挡板的仿真设计[J].表面技术,2022,51(4):342-347.
SUN Wei-chao,XU Jing,LIN Xing-kui,Ali.Esamdin.Simulation Design of Correction Masks for Optical Telescope Mirrors in Rotating Coating System[J].Surface Technology,2022,51(4):342-347
光学望远镜镜片旋转镀膜修正挡板的仿真设计
Simulation Design of Correction Masks for Optical Telescope Mirrors in Rotating Coating System
投稿时间:2020-12-23  修订日期:2021-10-15
DOI:10.16490/j.cnki.issn.1001-3660.2022.04.036
中文关键词:  真空镀膜  蒸发源  光学薄膜  膜厚均匀性  修正挡板  数值分析
英文关键词:film deposition  evaporation source  optical film  thickness uniformity  correction mask  numerical analysis
基金项目:新疆维吾尔自治区自然科学基金(2018D01B39)
作者单位
孙伟超 中国科学院新疆天文台,乌鲁木齐 830011 
许竞 中国科学院新疆天文台,乌鲁木齐 830011 
林星魁 中国科学院新疆天文台,乌鲁木齐 830011 
艾力.伊沙木丁 中国科学院新疆天文台,乌鲁木齐 830011 
AuthorInstitution
SUN Wei-chao Xinjiang Astronomical Observatory, Chinese Academy of Sciences, Urumqi 830011, China 
XU Jing Xinjiang Astronomical Observatory, Chinese Academy of Sciences, Urumqi 830011, China 
LIN Xing-kui Xinjiang Astronomical Observatory, Chinese Academy of Sciences, Urumqi 830011, China 
Ali.Esamdin Xinjiang Astronomical Observatory, Chinese Academy of Sciences, Urumqi 830011, China 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 提高新疆天文台南山观测基地ZZS1800-1/G真空镀膜机的膜厚均匀性指标。方法 通过建立旋转行星夹具系统的膜厚分布模型,利用高精度数值计算,基于ZZS1800-1/G真空镀膜机,研究镀膜机结构参数与镜面几何结构对膜厚均匀性的影响,分析蒸发源位置、望远镜镜片参数与修正挡板形状的关系,并进行修正挡板的仿真设计与验证。结果 在旋转行星夹具系统中,蒸发源与原点的距离对半径较大的镜面膜厚均匀性的影响最为明显。该距离600 mm以内,在镜面半径小于100 mm时,膜厚均匀性均低于1.7%;镜面半径为600 mm时,膜厚均匀性最佳,为23%。加入修正挡板后,膜厚均匀性理论计算值为0.035%。在镀半径为600 mm的镜片时,为保证均匀性小于1%,修正挡板的加工形变量要控制在2.2%以内。结论 加入修正挡板可有效提高ZZS1800-1/G真空镀膜机的膜厚均匀性,本文建立的仿真模型可为ZZS1800-1/G真空镀膜机在实际镀膜工作时修正挡板的设计提供理论参考依据。
英文摘要:
      This paper focuses on researching on the design method of correction masks utilizing for the mirror coating and aims to improve the film thickness uniformity based on ZZS1800-1/G vacuum coating machine, which equipped in Nanshan Station of Xinjiang Astronomical Observatory. By establishing the film thickness distribution model and using high precision numerical calculation, we studied the effects of structural parameters corresponding to ZZS1800-1/G vacuum coating machine and geometry structural parameters corresponding to different mirrors on film thickness uniformity, and analyzed the relevance between the shape of correction mask and the position of evaporate sources, parameters of the mirror, and display the simulation and numerical validation results of correction mask. Results showed that the distance between the evaporation source and the origin was the most obvious influence on the thickness uniformity of the mirror film with larger radius in the rotary planetary fixture system. When the distance was within 600 mm, and the mirror radius was less than 100 mm, and the uniformity of film thickness was less than 1.7%; when the mirror radius was 600 mm, the best uniformity of film thickness was 23%; and the theoretical value of the uniformity was 0.035% after adding correction mask, which shows the necessity of adding correction mask. The deformation of the correction mask needs to be within 2.2% for the purpose of keeping the uniformity less than 1% when the mirror radius was 600 mm. Correction mask can effectively improve the uniformity for ZZS1800-1/G vacuum coating machine, the simulation model proposed in this paper provides theoretical reference for the design of the masks.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第19497284位访问者    渝ICP备15012534号-3

版权所有:《表面技术》编辑部 2014 surface-techj.com, All Rights Reserved

邮编:400039 电话:023-68792193传真:023-68792396 Email: bmjs@surface-techj.com

渝公网安备 50010702501715号