田景睿,李慧,邹玉红,曾荣昌.医用镁合金表面肝素/蒙脱石涂层耐蚀性研究[J].表面技术,2021,50(2):66-73.
TIAN Jing-rui,LI Hui,ZOU Yu-hong,ZENG Rong-chang.Corrosion Resistance of Heparin/Montmorillonite Coating on Biomedical Magnesium Alloy[J].Surface Technology,2021,50(2):66-73
医用镁合金表面肝素/蒙脱石涂层耐蚀性研究
Corrosion Resistance of Heparin/Montmorillonite Coating on Biomedical Magnesium Alloy
投稿时间:2021-01-24  修订日期:2021-02-04
DOI:10.16490/j.cnki.issn.1001-3660.2021.02.008
中文关键词:  镁合金  肝素  耐蚀性能  蒙脱石  生物材料
英文关键词:magnesium alloy  heparin  corrosion resistance  montmorillonite  biomaterial
基金项目:山东省自然科学基金(ZR2020ME011)
作者单位
田景睿 山东科技大学化学与生物工程学院山东 青岛266590 
李慧 山东科技大学化学与生物工程学院山东 青岛266590 
邹玉红 山东科技大学化学与生物工程学院山东 青岛266590 
曾荣昌 山东科技大学材料科学与工程学院,山东 青岛266590 
AuthorInstitution
TIAN Jing-rui College of Chemical and Biological Engineering,, Qingdao 266590, China 
LI Hui College of Chemical and Biological Engineering,, Qingdao 266590, China 
ZOU Yu-hong College of Chemical and Biological Engineering,, Qingdao 266590, China 
ZENG Rong-chang College of Materials Science and Engineering, Shandong University of Scicnce and Technology, Qingdao 266590, China 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 为解决镁合金血管支架使血管内皮化、造成再狭窄等问题,在AZ31镁合金表面制备具有抗凝特性的肝素(HS)/蒙脱石(MMT)复合涂层,并研究其耐蚀性能。方法 采用水热法在AZ31镁合金表面制备钠蒙脱石(Na-MMT)涂层,在此基础上通过浸泡法以蒙脱石为载体,制备肝素/蒙脱石复合涂层。利用扫描电子显微镜(SEM)、傅里叶红外光谱仪(FT-IR)、X射线衍射仪(XRD)对所得涂层进行表面分析,通过电化学分析和析氢速率测定研究涂层的耐蚀性。结果 表面分析结果显示,通过水热法和浸泡法得到了均匀致密的HS-MMT涂层,厚度为41 mm。HS-MMT涂层的EDS元素分析图中出现了N、S及蒙脱石的基本元素,同时该涂层的FT-IR和XRD图出现了肝素及蒙脱石的特征峰。耐蚀性研究显示,与AZ31镁合金相比,HS-MMT涂层的自腐蚀电位升高了0.29 V,腐蚀电流密度降低了2个数量级,且其平均析氢速率为0.016 mL/(cm×h),仅为AZ31镁合金平均析氢速率的18%。 结论 采用水热法和浸泡法在AZ31镁合金表面成功制备了HS-MMT涂层,该涂层具有良好的耐蚀性能,为镁合金血管支架的研究提供了一种新方案。
英文摘要:
      To solve the problems such as vascular endothelialization and restenosis caused by magnesium alloy stent, this study aims to prepare heparin (HS)/montmorillonite (MMT) coating with anticoagulant properties on biomedical magnesium alloy and investigate its corrosion resistance. Sodium montmorillonite (Na-MMT) coating was prepared on the surface of AZ31 magnesium alloy by hydrothermal method; and then HS/MMT composite coating was prepared by immersion method. The coating was characterized using scanning electron microscopy (SEM), Fourier infrared spectroscopy (FT-IR) and X-ray diffractometry (XRD). The corrosion resistance of the coating was investigated by means of electricchemical analysis and hydrogen evolution rate measurement. The results showed that the prepared HS-MMT coating was uniform and compact, with coating thickness of 41 mm. The basic elements of montmorillonite and N, S were found in the EDS analysis diagram of HS-MMT coating, and the characteristic peaks of heparin and montmorillonite were found in the FT-IR and XRD images of the coating. Compared with the AZ31 magnesium alloy, the free corrosion potential of HS-MMT coating was increased up to 0.29 V; corrosion current density was decreased by two orders of magnitude; and the average hydrogen evolution rate was 0.016 mL/(cm×h), only 18% of the AZ31 substrate. Therefore, the HS-MMT coating has good corrosion resistance, providing a new scheme for magnesium alloy vascular stents.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第19513529位访问者    渝ICP备15012534号-3

版权所有:《表面技术》编辑部 2014 surface-techj.com, All Rights Reserved

邮编:400039 电话:023-68792193传真:023-68792396 Email: bmjs@surface-techj.com

渝公网安备 50010702501715号