刘云,李丽,李瑶,林本刚,赵林,张岩.复合电极-混粉电火花加工Ti-6Al-4V钛合金的研究[J].表面技术,2017,46(9):252-257.
LIU Yun,LI Li,LI Yao,LIN Ben-gang,ZHAO Lin,ZHANG Yan.Composite Electrode-Powder Mixed Electric Discharge Machining Ti-6Al-4V Titanium Alloy[J].Surface Technology,2017,46(9):252-257
复合电极-混粉电火花加工Ti-6Al-4V钛合金的研究
Composite Electrode-Powder Mixed Electric Discharge Machining Ti-6Al-4V Titanium Alloy
投稿时间:2017-03-15  修订日期:2017-09-20
DOI:10.16490/j.cnki.issn.1001-3660.2017.09.040
中文关键词:  表面形貌  熔凝层  显微硬度  表面粗糙度  电极损耗  混粉电火花加工
英文关键词:surface morphology  melting layer  microhardness  surface roughness  electrode loss  powder mixed edm
基金项目:国家自然科学基金(51105235)
作者单位
刘云 山东理工大学 机械工程学院,山东 淄博 255049 
李丽 山东理工大学 机械工程学院,山东 淄博 255049 
李瑶 山东理工大学 机械工程学院,山东 淄博 255049 
林本刚 山东理工大学 机械工程学院,山东 淄博 255049 
赵林 山东理工大学 机械工程学院,山东 淄博 255049 
张岩 山东理工大学 机械工程学院,山东 淄博 255049 
AuthorInstitution
LIU Yun School of Mechanical Engineering, Shandong University of Technology, Zibo 255049, China 
LI Li School of Mechanical Engineering, Shandong University of Technology, Zibo 255049, China 
LI Yao School of Mechanical Engineering, Shandong University of Technology, Zibo 255049, China 
LIN Ben-gang School of Mechanical Engineering, Shandong University of Technology, Zibo 255049, China 
ZHAO Lin School of Mechanical Engineering, Shandong University of Technology, Zibo 255049, China 
ZHANG Yan School of Mechanical Engineering, Shandong University of Technology, Zibo 255049, China 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 采用混粉电火花加工技术,使用超声电沉积制备的Cu-SiC复合电极加工TC4钛合金,在工作液中混入碳粉进行表面改性,以获取性能优异的加工表面。方法 利用Cu-SiC复合电极和Cu电极对TC4钛合金进行成型加工。用扫描电子显微镜(SEM)观察加工后工件的表面形貌和熔凝层断面形貌,并用TR200粗糙度仪测量其表面不同位置的粗糙度值。用硬度仪测量工件熔凝层的显微硬度,用X射线衍射仪对材料强化层进行物相分析。并对电极损耗进行对比分析。结果 Cu电极加工的TC4钛合金表面凹坑深且面积大,熔凝层疏松,粘合性较差。Cu-SiC复合电极加工的TC4钛合金表面放电痕迹大,深度统一,电蚀产物少,熔凝层致密好。利用X射线衍射仪、硬度测量仪和粗糙度仪对试样测量分析显示,Cu-SiC复合电极加工后,表面生成的TiC峰相高,耐磨性好,表层显微硬度较大,约为基体的6倍,表面平均粗糙度值Ra=2.825 µm。复合电极损耗比铜电极损耗降低了18%。结论 两种电极加工后,TC4钛合金表面均得到改善,且使用超声电沉积Cu-SiC复合电极加工后的表面质量更好。
英文摘要:
      The work aims to complete surface modification by processing TC4 titanium alloy with Cu-SiC composite electrode prepared by ultrasonic electrolytic deposition and mixing carbon powder into working fluid, so as to obtain surface with excellent properties. TC4 titanium alloy was formed by using Cu-SiC composite electrode and Cu electrode. Firstly, morphology of the machined workpiece and fracture morphology of the melting layer were observed with scanning electron microscope (SEM), and roughness values in different positions on the surface were measured with TR200 roughness meter. Then microhardness of the workpiece's melting layer was measured with FM800 hardness tester, phase analysis of the strengthened layer was carried out by using X-ray diffractometer. Finally, electrode losses were compared and analyzed. The surface of TC4 titanium alloy machined by Cu electrode featured in deep and large pit, loose melting layer and poor adhesion. The surface of TC4 titanium alloy processed by Cu-SiC composite electrode featured in large traces of discharge, uniform depth, few discharge debris and compact melting layer. Measurement analysis from X ray diffractometer, FM800 hardness tester and roughness tester showed that workpiece surface machined by Cu-SiC composite electrode exhibited higher TiC peak, better abrasion resistance and higher hardness. The surface microhardness was about 6 times of the substrate, and average surface roughness value Ra was 2.825 µm. Loss of the composite electrode was 18% lower than that of copper electrode. The surface of TC4 titanium alloy is improved, surface of TC4 titanium alloy is improved, and the surface quality of Cu-SiC composite electrode subject to ultrasonic-electrodeposition is better than that of Cu electrode.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第21802368位访问者    渝ICP备15012534号-3

版权所有:《表面技术》编辑部 2014 surface-techj.com, All Rights Reserved

邮编:400039 电话:023-68792193传真:023-68792396 Email: bmjs@surface-techj.com

渝公网安备 50010702501715号