刘飞,毛杰,邓子谦,邓春明,张小锋,邓畅光,刘敏.等离子喷涂-物理气相沉积制备热障涂层对气膜冷却孔的影响[J].表面技术,2017,46(8):21-26.
LIU Fei,MAO Jie,DENG Zi-qian,DENG Chun-ming,ZHANG Xiao-feng,DENG Chang-guang,LIU Min.Effects of Thermal Barrier Coatings Prepared by Plasma-spray Physical Vapor Deposition on Air Film Cooling Hole Contraction[J].Surface Technology,2017,46(8):21-26
等离子喷涂-物理气相沉积制备热障涂层对气膜冷却孔的影响
Effects of Thermal Barrier Coatings Prepared by Plasma-spray Physical Vapor Deposition on Air Film Cooling Hole Contraction
投稿时间:2017-01-09  修订日期:2017-08-20
DOI:10.16490/j.cnki.issn.1001-3660.2017.08.004
中文关键词:  等离子喷涂-物理气相沉积  热障涂层  气膜冷却孔  孔径收缩率  柱状涂层  堵孔
英文关键词:plasma spray-physical vapor deposition  thermal barrier coating  air film cooling hole  shrinkage factor of pore size  columnar coating  hole blockage
基金项目:广东省对外合作项目(2013B050800027);广州市对外合作项目(201508030001);广东省自然科学基金项目(2016A030312015)
作者单位
刘飞 1.华南理工大学 材料科学与工程学院,广州 510640;2.广东省新材料研究所 现代材料表面工程技术国家工程实验室 广东省现代表面工程技术重点实验室,广州 510651 
毛杰 广东省新材料研究所 现代材料表面工程技术国家工程实验室 广东省现代表面工程技术重点实验室,广州 510651 
邓子谦 广东省新材料研究所 现代材料表面工程技术国家工程实验室 广东省现代表面工程技术重点实验室,广州 510651 
邓春明 广东省新材料研究所 现代材料表面工程技术国家工程实验室 广东省现代表面工程技术重点实验室,广州 510651 
张小锋 广东省新材料研究所 现代材料表面工程技术国家工程实验室 广东省现代表面工程技术重点实验室,广州 510651 
邓畅光 广东省新材料研究所 现代材料表面工程技术国家工程实验室 广东省现代表面工程技术重点实验室,广州 510651 
刘敏 广东省新材料研究所 现代材料表面工程技术国家工程实验室 广东省现代表面工程技术重点实验室,广州 510651 
AuthorInstitution
LIU Fei 1.School of Materials Science and Engineering, South China University of Technology, Guangzhou 510640, China; 2.Guangdong Institute of New Materials, National Engineering Laboratory for Modern Materials Surface Engineering Technology, Key Laboratory of Guangdong for Modern Surface Engineering Technology, Guangzhou 510651, China 
MAO Jie Guangdong Institute of New Materials, National Engineering Laboratory for Modern Materials Surface Engineering Technology, Key Laboratory of Guangdong for Modern Surface Engineering Technology, Guangzhou 510651, China 
DENG Zi-qian Guangdong Institute of New Materials, National Engineering Laboratory for Modern Materials Surface Engineering Technology, Key Laboratory of Guangdong for Modern Surface Engineering Technology, Guangzhou 510651, China 
DENG Chun-ming Guangdong Institute of New Materials, National Engineering Laboratory for Modern Materials Surface Engineering Technology, Key Laboratory of Guangdong for Modern Surface Engineering Technology, Guangzhou 510651, China 
ZHANG Xiao-feng Guangdong Institute of New Materials, National Engineering Laboratory for Modern Materials Surface Engineering Technology, Key Laboratory of Guangdong for Modern Surface Engineering Technology, Guangzhou 510651, China 
DENG Chang-guang Guangdong Institute of New Materials, National Engineering Laboratory for Modern Materials Surface Engineering Technology, Key Laboratory of Guangdong for Modern Surface Engineering Technology, Guangzhou 510651, China 
LIU Min Guangdong Institute of New Materials, National Engineering Laboratory for Modern Materials Surface Engineering Technology, Key Laboratory of Guangdong for Modern Surface Engineering Technology, Guangzhou 510651, China 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 研究等离子喷涂-物理气相沉积(PS-PVD)制备热障涂层过程中影响气膜冷却孔堵塞情况的因素。方法 采用等离子喷涂-物理气相沉积技术,以团聚烧结的ZrO2-7%Y2O3(7YSZ)为原料,在预制有气膜冷却孔的高温合金板基体上制备热障涂层,研究了气膜冷却孔的孔角度、孔径大小等参数在热障涂层制备过程中对气膜孔堵塞情况的影响。结果 当气膜冷却孔的孔径控制为0.85 mm时,30°、60°、90°气膜冷却孔的孔径收缩率分别为19.01%、14.50%、14.86%,孔径收缩率随角度的增大而减小,一定程度后保持稳定。孔内部涂层结构与表面涂层结构一致,都为柱状结构涂层。当气膜冷却孔的角度控制为30°时,孔径为1.0、1.3、15 mm的气膜冷却孔的孔径收缩率分别为36.40%、31.70%、24.45%,孔径收缩率随孔径的增大而减小。涂层在孔内的分布深度随孔径大小的增大而增大。结论 气膜冷却孔的角度会影响PS-PVD热障涂层的沉积效率,从而影响孔径收缩率。气膜冷却孔的孔径不影响PS-PVD热障涂层的沉积效率,但会影响孔径收缩率。
英文摘要:
      The work aims to study factors affecting blocking of air film cooling hole during preparation of thermal barrier coating by plasma-spray physical vapor deposition. With agglomerated and sintered ZrO2-7wt%Y2O3(7YSZ) powder as raw material, thermal barrier coatings were prepared by plasma spray-physical vapor deposition (PS-PVD) on superalloy plate substrate with precast air film cooling holes. Effects of parameters including hole angle and pore size of the air film cooling hole on hole blockage were studied. When pore size of the air film cooling hole was controlled within 0.85 mm, shrinkage factor of the pore size was 19.01%, 14.50%, 14.86%, respectively at the angle of 30°, 60°and 90°. Shrinkage factor of the pore size decreased and maintained stable after a while as the angle increased. Both coatings outside and inside the hole were of columnar structure. When the angle of air film cooling hole was 30°, shrinkage factor of the pore size was 36.40%, 31.70% and 24.45%, respectively provided with pore size of 1.0 mm, 1.3 mm and 1.5 mm. The shrinkage factor decreased while distribution depth of the coating in hole increased as the pore size increased. The angle of air film cooling hole will influence deposition efficiency of thermal barrier coatings, and thus affecting shrinkage factor of pore size. Pore size of the air film cooling hole has no effect on deposition efficiency of thermal barrier coatings, but it will affect shrinkage factor of pore size.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第19496640位访问者    渝ICP备15012534号-3

版权所有:《表面技术》编辑部 2014 surface-techj.com, All Rights Reserved

邮编:400039 电话:023-68792193传真:023-68792396 Email: bmjs@surface-techj.com

渝公网安备 50010702501715号