郑英.双辉等离子渗铬与高碳钢淬火的耐磨性比较[J].表面技术,2017,46(4):186-190.
ZHENG Ying.Comparative Study on Wear Resistance of High Carbon Quenching and Double Glow Plasma Chromizing[J].Surface Technology,2017,46(4):186-190
双辉等离子渗铬与高碳钢淬火的耐磨性比较
Comparative Study on Wear Resistance of High Carbon Quenching and Double Glow Plasma Chromizing
投稿时间:2016-09-11  修订日期:2017-04-20
DOI:10.16490/j.cnki.issn.1001-3660.2017.04.030
中文关键词:  双辉等离子渗铬  磨粒磨损  耐磨性
英文关键词:double glow plasma chromizing  abrasive wear  abradability
基金项目:湖南省教育厅科研课题(13C254)
作者单位
郑英 湖南交通职业技术学院,长沙 410132 
AuthorInstitution
ZHENG Ying Hunan Communication Polytechnic, Changsha 410132, China 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 研究相变点下双辉等离子渗铬的渗层在磨粒磨损条件下的耐磨性能。方法 采用低温双辉等离子渗金属技术,在高碳钢表面直接形成高硬度渗层,比较研究T10钢整体淬火+低温回火(以下简称T10钢淬火)与调质态T10钢经550 ℃×8 h预先离子氮化再经560 ℃×4 h双辉等离子渗铬(以下简称T10钢低温渗铬)的耐磨粒磨损性能。结果 在400#砂纸摩擦磨损条件下,T10钢淬火的磨损质量损失面积比率为3.5669×10-5g/mm2,远小于T10钢低温渗铬(2.9936×10-4g/mm2),其耐磨性是T10钢低温渗铬的近7倍;在2000#砂纸摩擦磨损条件下,T10钢低温渗铬的磨损质量损失面积比率为6.3694×10-6g/mm2,小于T10钢整体淬火(1.2739×10-5g/mm2),其渗层耐磨性约为T10钢整体淬火的2倍。结论 低温双辉等离子渗铬的渗层适用于小磨粒状态下的摩擦环境,磨粒的尺度应小于或与渗层的厚度相当。
英文摘要:
      To study wear resistance of chromizing layer of double glow plasma chromizing in phase transformation point under abrasive wear. Low temperature double glow plasma chromizing etc. were adopted to form a chromizing layer directly on the high-carbon steel surface. The abrasive resistance of abrasive wear in integral quenching of T10 steel + low temperature tempering (shorted as T10 quenching) and T10 pre-nitriding at 550 ℃×8 h+560 ℃×4 h chromizing (shorted as T10 steel low temperature chromizing) was studied comparatively. In the wearing condition of 400# sand paper, the area ratio of wear mass loss of T10 low temperature chromizing was 2.9936×10-4 g/mm2; that of the T10 quenching was 3.5669×10-5 g/mm2; it was far less than that of T10 low temperature chromizing; its wear resistance was nearly 7 times of the T10 quenching; in the wearing condition of 2000# sand paper, the area ratio of wear mass loss of T10 quenching was 1.2739×10-5 g/mm2; that of the T10 low temperature chromizing was 6.3694×10-6 g/mm2 , it was much less than that of T10 integral quenching; the wear resistance of T10 low temperature chromizing was 2 times of the T10 quenching. The chromizing layer of low temperature double glow plasma is applicable to small abrasive wear, and abrasive particle size must be less than or equal to size of chromizing layer.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第19501688位访问者    渝ICP备15012534号-3

版权所有:《表面技术》编辑部 2014 surface-techj.com, All Rights Reserved

邮编:400039 电话:023-68792193传真:023-68792396 Email: bmjs@surface-techj.com

渝公网安备 50010702501715号