陈光忠,何志坚,杨岳.AISI-304奥氏体不锈钢喷丸残余应力的有限元模拟[J].表面技术,2016,45(12):124-128.
CHEN Guang-zhong,HE Zhi-jian,YANG Yue.Finite Element Simulation of Residual Stress of Shot Peening on AISI-304 Austenitic Stainless Steel[J].Surface Technology,2016,45(12):124-128
AISI-304奥氏体不锈钢喷丸残余应力的有限元模拟
Finite Element Simulation of Residual Stress of Shot Peening on AISI-304 Austenitic Stainless Steel
投稿时间:2016-05-07  修订日期:2016-12-20
DOI:10.16490/j.cnki.issn.1001-3660.2016.12.020
中文关键词:  AISI-304  有限元  随机多弹丸喷丸  残余应力  覆盖率  工艺参数
英文关键词:AISI-304  finite element  random multi-shot peening  residual stress  coverage rate  technological parameters
基金项目:湖南省科技厅研究课题(2013FJ3019);湖南省教育厅研究课题(14C0825)
作者单位
陈光忠 湖南信息职业技术学院,长沙 410200 
何志坚 湖南信息职业技术学院,长沙 410200 
杨岳 中南大学 交通运输工程学院,长沙 410083 
AuthorInstitution
CHEN Guang-zhong Hunan College of Information, Changsha 410200, China 
HE Zhi-jian Hunan College of Information, Changsha 410200, China 
YANG Yue School of Traffic and Transportation Engineering, Central South University, Changsha 410083, China 
摘要点击次数:
全文下载次数:
中文摘要:
      目的 针对喷丸有限元模拟中多数模型的弹丸数量较少,不能准确反映喷丸过程中弹丸位置的随机性及喷丸覆盖率对残余应力场影响的问题,对喷丸过程的有限元模拟技术进行优化。方法 基于大型有限元分析软件ABAQUS,使用python编程语言对弹丸在三维空间中的分布进行随机化处理,建立了随机多弹丸喷丸AISI-304奥氏体不锈钢的有限元模型。在喷丸覆盖率大于100%的条件下,模拟分析了喷丸工艺中弹丸的数量、尺寸和弹丸的速度对残余应力场的影响,结合试验对有限元模型的合理性进行了验证。结果 增加弹丸数量可提高残余压应力层的厚度和残余压应力的最大值,当弹丸数量为90颗时,残余压应力场接近饱和;增加弹丸速度,靶材残余压应力的峰值、表面应力值及残余压应力场的深度值增大,残余压应力峰值出现的位置基本不变;增大弹丸的直径,靶材残余压应力峰值、峰值的位置、表面应力值及残余压应力场的深度值均明显增大。结论 喷丸残余应力的试验测量结果和有限元模拟结果吻合,模型合理。
英文摘要:
      The work aims to optimize the finite element simulation technology of shot peening technology since limited shots are used by most models in finite element simulation of shot peening, randomness of shot position and the effects of shot peening coverage to residual stress field are not accurately reflected. By virtue of a large-scale finite element analysis software ABAQUS, python programming language was used to randomize the distribution of shots in three-dimensional space and finite element model of random multi-shot shot peening was established. Provided that coverage rate of shot peening exceeds 100%, effects of shot quantity, size and velocity of shot peening technology on residual stress field were analyzed and simulated, and the rationality of the finite element model was verified by experiment. Thickness of compressive residual stress layer and the maximum residual stress could be increased by adding shots. The residual stress field was nearly satured when there were 90 shots. As the shot velocity increased, the peak value of residual stress on target, surface stress value and the depth of residual stress field increased and the site where residual stress peak was present kept unchanged. As the shot diameter increased, peak value of residual stress on target, surface stress value and the depth of residual stress field increased significantly. The measurement results of shot peening residual stress test are consistent with that of finite element simulation and the finite element model is reasonable.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第19511654位访问者    渝ICP备15012534号-3

版权所有:《表面技术》编辑部 2014 surface-techj.com, All Rights Reserved

邮编:400039 电话:023-68792193传真:023-68792396 Email: bmjs@surface-techj.com

渝公网安备 50010702501715号