曾凡勇,李养良,张德勤,李海洲,潘东,倪晓峰.热镀锌法提高B82MnQL材料的抗拉强度研究[J].表面技术,2016,45(3):96-102.
ZENG Fan-yong,LI Yang-liang,ZHANG De-qin,LI Hai-zhou,PAN Dong,NI Xiao-feng.Study on the tensile strength of B82MnQL materials by hot dip galvanizing[J].Surface Technology,2016,45(3):96-102 |
| 热镀锌法提高B82MnQL材料的抗拉强度研究 |
| Study on the tensile strength of B82MnQL materials by hot dip galvanizing |
| 投稿时间：2015-11-16 修订日期：2016-03-20 |
| DOI：10.16490/j.cnki.issn.1001-3660.2016.03.016 |
| 中文关键词: BB82MnQL盘条 拉拔 镀锌 镀锌钢丝 稳定化处理 抗拉强度 |
| 英文关键词:B82MnQL wire rod drawing galvanized galvanizing steel wire stabilization treatment tensile strength |
| 基金项目:2013年九江学院校级科研项目(2013ZD07),江西省教育厅科技落地计划项目(KJLD14091)江西省首批“卓越工程师教育培养计划”实施成果“赣财教2011[244]号”。第一作者：曾凡勇(1989-),男,九江学院2009级材料成型及控制工程专业学生。通讯作者：李养良(1966-),男,江西九江人,教授,主要从事机械设计及材料表面改性研究。 ,张德勤1,李海洲1,潘东1,倪晓峰2 |
|
|
| Author | Institution |
| ZENG Fan-yong | School of Mechanical and Materials Engineering, Jiujiang University, Jiujiang 332005, China |
| LI Yang-liang | School of Mechanical and Materials Engineering, Jiujiang University, Jiujiang 332005, China |
| ZHANG De-qin | School of Mechanical and Materials Engineering, Jiujiang University, Jiujiang 332005, China |
| LI Hai-zhou | School of Mechanical and Materials Engineering, Jiujiang University, Jiujiang 332005, China |
| PAN Dong | School of Mechanical and Materials Engineering, Jiujiang University, Jiujiang 332005, China |
| NI Xiao-feng | Ossen Innovation Materials Co. , Ltd, Jiujiang 332000, China |
|
| 摘要点击次数: |
| 全文下载次数: |
| 中文摘要: |
| 目的 增强B82MnQL材料的抗拉强度。 方法 以B82MnQL盘条作为热镀锌的试验材料，利用拉伸试验机、反复弯曲试验机对其力学性能进行了测试，借助金相显微镜、扫描电镜分析了几种镀锌工艺下的横截面和轴向截面以及拉拔断口的组织形貌，测试了显微硬度。结果 B82MnQL盘条拉拔后钢丝的抗拉强度由原来的1250MPa提高至1670MPa。断面收缩率由32.5%下降至7%。采用新镀锌工艺和助镀配方，B82MnQL钢丝镀锌后抗拉强度下降幅度为8%，低于传统的10-15%，稳定化后B82MnQL的扭转值20次左右，反复弯曲6次左右，强度由1650MPa提高至1710MPa，硬度值比镀锌后有较大提高，由镀锌后的430HV升高至450HV，而且分布均匀。结论 通过镀锌工艺优化，能使B82MnQL盘条的抗拉强度有较大的提高。 |
| 英文摘要: |
| The B82MnQL wire rod for used as the material for hot dip galvanizing experiment, using tensile testing machine, repeated bending testing machine on the mechanical properties were tested。The microstructure of the cross section、the axial section and the drawing fracture were analyzed by means of optical microscope and scanning electron microscope.The results show：The B82MnQL wire rod tensile strength increased from 1250MPa to 1670MPa.The shrinkage rate of the cross section decreased from 32.5% to 7%.Used the new technology and the formula of the assistant plating,the tensile strength of the B82MnQL steel wire after galvanized was decreased by 8%,lower than traditional 10-15%. After stabilization , the B82MnQL"s torsion value about 20 times, repeated bending about 6 times, strength increased from 1710MPa to 1650MPa, The hardness value is higher than that of the galvanized, raised from 430HV to 450HV, and uniformly dispersed. |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| 关闭 |
|
|
|
渝公网安备 50010702501715号