壮筱凯,李庆忠.雾化施液抛光硅片位错的化学腐蚀形貌分析[J].表面技术,2015,44(5):129-135.
ZHUANG Xiao-kai,LI Qing-zhong.Chemical Corrosion Morphology Analysis of Dislocations of Silicon Wafer Polished by Ultrasonic Atomization CMP[J].Surface Technology,2015,44(5):129-135 |
| 雾化施液抛光硅片位错的化学腐蚀形貌分析 |
| Chemical Corrosion Morphology Analysis of Dislocations of Silicon Wafer Polished by Ultrasonic Atomization CMP |
| 投稿时间：2015-01-19 修订日期：2015-05-20 |
| DOI：10.16490/j.cnki.issn.1001-3660.2015.05.024 |
| 中文关键词: 雾化施液 硅片 位错腐蚀坑 传统抛光 雾化参数 |
| 英文关键词:ultrasonic atomization silicon wafer dislocation etch pit traditional CMP atomization parameters |
| 基金项目:国家自然科学基金项目(51175228) |
|
|
|
|
| 摘要点击次数: |
| 全文下载次数: |
| 中文摘要: |
| 目的 研究硅片经雾化施液抛光技术加工后存在的位错缺陷。 方法 应用化学腐蚀法、光学方法分析硅片不同部位的位错腐蚀形貌、位错密度及其分布,通过单因素实验研究雾化参数对位错形貌和位错密度的影响规律。 在相同的工艺参数下,和传统抛光进行对比实验。 结果 雾化抛光硅片的平均位错密度为 1. 2×104 / cm2,边沿处的位错密度小于其他区域。 在相同的工艺参数下,雾化施液 CMP 的抛光液消耗量约为传统 CMP 的 1 /10,但硅片的位错腐蚀形貌和位错密度明显好于传统抛光,且蚀坑分布均匀分散,没有出现位错排等严重缺陷。 通过增大雾化器的出雾量能有效改善硅片表层的位错缺陷。 结论相对于传统抛光,雾化施液抛光技术能更加高效地去除硅片的位错缺陷。 |
| 英文摘要: |
| Objective To study the dislocation defect of silicon wafer which was polished by ultrasonic atomization chemical mechanical polishing (CMP). Methods The chemical etching method and optics method were used to analyze the morphology, density, and distribution of the dislocation etch pits. Besides, the influence of atomization quantity on the morphology and density of dislocation was studied by single factor experiment. Then comparative experiments were conducted with traditional CMP under the same conditions. Results The average dislocation density of the polished silicon wafer was about 1. 2×104 / cm2 and the dislocation density in edge area was lower than other areas. Besides, the dislocation morphology and dislocation density of silicon wafer polished by ultrasonic atomization CMP were obviously better than those treated by traditional CMP under the same conditions while the polishing liquid consumption was about one tenth of traditional CMP. The dislocation etch pits distributed evenly and there were no serious flaws such as dislocation piles and so on. In addition to that, the dislocation defect could be effectively improved by increasing the quantity of atomization. Conclusion Ultrasonic atomization CMP removed the dislocation defect of silicon wafer more efficiently than traditional CMP. |
| 查看全文 查看/发表评论 下载PDF阅读器 |
| 关闭 |
|
|
|
渝公网安备 50010702501715号