刘迎新,余取民,刘婷琛,何协华.清洁型免水洗常温锰钙钡系磷化液的研究[J].表面技术,2013,42(2):89-91,100.
LIU Ying-xin,YU Qu-min,LIU Ting-chen,HE Xie-hua.Study on Cleaning and Free-washing Mn-Ca-Ba Phosphating Solution at Room Temperature[J].Surface Technology,2013,42(2):89-91,100
清洁型免水洗常温锰钙钡系磷化液的研究
Study on Cleaning and Free-washing Mn-Ca-Ba Phosphating Solution at Room Temperature
投稿时间:2012-11-05  修订日期:2012-12-14
DOI:
中文关键词:  锰钙钡系磷化液  常温  免水洗
英文关键词:Mn-Ca-Ba phosphating solution  room temperature  free washing
基金项目:长沙市科技局项目( K1205054-11) ;长沙学院人才引进基金项目( SF080404)
作者单位
刘迎新 长沙学院, 长沙 410003 
余取民 长沙学院, 长沙 410003 
刘婷琛 长沙学院, 长沙 410003 
何协华 长沙学院, 长沙 410003 
AuthorInstitution
LIU Ying-xin Changsha University, Changsha 410003 , China 
YU Qu-min Changsha University, Changsha 410003 , China 
LIU Ting-chen Changsha University, Changsha 410003 , China 
HE Xie-hua Changsha University, Changsha 410003 , China 
摘要点击次数:
全文下载次数:
中文摘要:
      以磷酸二氢锰、硝酸钙、硝酸钡、钼酸钠等为原料配制锰钙钡系磷化液,对 Q235 钢铁试片进行常温磷化,磷化后免水洗,自然干燥 3 h 以上,获得了彩色锰钙钡系磷化膜。 分析了磷化膜的形貌和组成,考察了磷化液 pH 值、磷化温度、磷化时间、磷化量等工艺条件对磷化膜性能的影响。 结果表明,在磷化液 pH 值 2 . 3 ~ 2 . 8 、磷化温度 5 ~ 40 益 下浸渍磷化 8 ~ 10 min,可生成连续、致密且颗粒细小的免水洗锰钙钡系磷化膜;磷化膜由 Fe,Mn,Ca,Ba 的磷酸盐及少量钼酸盐等组成,耐硫酸铜溶液腐蚀时间>85 s,膜质量 0 . 9 g / m2左右,喷涂铁红环氧底漆后的涂层附着力达 1 级。
英文摘要:
      Q235 Steel specimen was phosphated at room temperature in the Mn-Ca-Ba phosphating solution consisting of manganese dihydrogen phosphate, calcium nitrate, barium nitrate and sodium molybdate. Washing-free, colorful phosphate coating was formed after natural drying for 3 hours. The effect of pH value, temperature, treatment time and the lifetime of phosphating solution on the properties of the phosphate coating was investigated. Moreover, the morphology and component of the phosphate coating were analyzed. The results show that continuous and compact phosphate coating is obtained when the specimen is phosphated for 8 ~ 10 min under 5 ~ 40 益 with phosphating solution, whose pH value is 2 . 3 ~ 2 . 8 . The particles of the phosphate coating are very fine. The phosphating coating is composed of phosphate of Fe, Mn, Ca and Ba and a little of molybdate. The time of copper sulphate solution corrosion resistance is more than 85 s, and the weight of coating is around 0 . 9 g /m2. The adhesion of the coating reaches 1 grade after being sprayed with iron-red epoxy primer.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第20096414位访问者    渝ICP备15012534号-3

版权所有:《表面技术》编辑部 2014 surface-techj.com, All Rights Reserved

邮编:400039 电话:023-68792193传真:023-68792396 Email: bmjs@surface-techj.com

渝公网安备 50010702501715号