江强,武晓南,周细应,言智,毛秀娟,李明.柔性基底上直流磁控溅射沉积金属铝膜的研究[J].表面技术,2013,42(1):67-70.
JIANG Qiang,WU Xiao-nan,ZHOU Xi-ying,YAN Zhi,MAO Xiu-juan,LI Ming.Research on Al Thin Films Deposited on the Flexible Base Materials[J].Surface Technology,2013,42(1):67-70
柔性基底上直流磁控溅射沉积金属铝膜的研究
Research on Al Thin Films Deposited on the Flexible Base Materials
投稿时间:2012-08-22  修订日期:2012-10-01
DOI:
中文关键词:  磁控溅射  柔性基底  铝膜
英文关键词:magnetron sputtering  flexible substrate  Al thin film
基金项目:上海市教委科技发展基金(11CXY57) ;上海市教委大学生创新实践计划项目( CX1121009 ) ;上海工程技术大学研究生科研创新项目(2011yjs18) ;上海高校一流学科建设计划( YLJX12-2)
作者单位
江强 上海工程技术大学 材料工程学院, 上海 201620 
武晓南 上海工程技术大学 材料工程学院, 上海 201620 
周细应 上海工程技术大学 材料工程学院, 上海 201620 
言智 上海工程技术大学 材料工程学院, 上海 201620 
毛秀娟 上海工程技术大学 材料工程学院, 上海 201620 
李明 上海工程技术大学 材料工程学院, 上海 201620 
AuthorInstitution
JIANG Qiang School of Material Engineering, Shanghai University of Engineering Science, Shanghai 201620 , China 
WU Xiao-nan School of Material Engineering, Shanghai University of Engineering Science, Shanghai 201620 , China 
ZHOU Xi-ying School of Material Engineering, Shanghai University of Engineering Science, Shanghai 201620 , China 
YAN Zhi School of Material Engineering, Shanghai University of Engineering Science, Shanghai 201620 , China 
MAO Xiu-juan School of Material Engineering, Shanghai University of Engineering Science, Shanghai 201620 , China 
LI Ming School of Material Engineering, Shanghai University of Engineering Science, Shanghai 201620 , China 
摘要点击次数:
全文下载次数:
中文摘要:
      采用直流磁控溅射法在棉布、涤纶、芳纶织物上制备金属铝膜,研究了铝膜的沉积速率、组织结构和表面形貌。 结果表明:在一定的范围内,沉积速率随溅射功率的增大近似呈线性增加,随溅射气压的增加先升后降;基底材料对铝膜的组织结构有较大影响,在涤纶和棉布上沉积的铝膜才呈现出典型的多晶态面心立方结构,在芳纶和涤纶上获得的铝膜较棉布上的铝膜更为均匀、致密;在一定范围内,溅射功率的增大有助于提高铝膜质量。
英文摘要:
      Al thin films were respectively deposited by DC magnetron sputtering on the flexible substrates, such as the polyester , the aramid and the cotton etc. The deposition rate, structure and surface morphology of the aluminum thin films were studied. The results show that the deposition rate increases almost linearly with increasing sputtering power in a certain range. On the other hand, the deposition rate increases with increasing working pressure then decreases when it came up to the maximum peak. The crystal structures of the films are influenced due to the different substrates. The films on the polyester and cotton only have typical polycrystalline face-centered cubic structure. The films on the aramid and polyester are more uniform density and the particles are smaller than the ones on the cotton. Within a certain range, the increase of the sputtering power does enhance the quality of the thin films.
查看全文  查看/发表评论  下载PDF阅读器
关闭

关于我们 | 联系我们 | 投诉建议 | 隐私保护 | 用户协议

您是第19991736位访问者    渝ICP备15012534号-3

版权所有:《表面技术》编辑部 2014 surface-techj.com, All Rights Reserved

邮编:400039 电话:023-68792193传真:023-68792396 Email: bmjs@surface-techj.com

渝公网安备 50010702501715号